D26441K-AR (Type 1) DeWALT Sander Polisher - Overview

This is a genuine OEM replacement part, it is sold individually. This part is used to keep the brush tight against the armature so the tool will work properly. Over time when the brushes wear down and heat is created, the spring may lose its tension and will have to be replaced.

It is a high-quality OEM part that is specially made for Porter Cable, Black and Decker and DeWALT power tools. The receptacle is designed to safely secure and connect a wire. It is an identical replacement for a faulty or a missing part that was installed on a new unit. To ensure the correct application, refer to the appropriate diagrams...Read more of your model. Note, this high-quality receptacle is made of durable metal and is sold individually. You will need a screwdriver to take the housing apart when replacing this component.

This is a Genuine Manufacturer Sourced replacement part used on a variety of Sanders. This part is made out of Plastic and it is Sold Individually. This part is secured over Switch providing protection from the dust.

This replacement screw is a high quality hardware that is specially manufactured for use with Dewalt, Black and Decker and Porter Cable power tools. It is a authentic OEM sourced item that has multiple applications depending on the unit, for correct location and use of this screw make sure to check appropriate diagrams. Please note this torx screw is sold individually.

O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-ring failure. The most common among power tools are: • The O-ring has ragged, tattered edges. These are commonly caused by pressure ...Read morespikes which shear off tiny "bites" from the O-ring, or caused by clearance gaps. • One or both sides of the O-ring appear rough and slightly flattened. Commonly caused by a contact surface that is too rough, contains grit, or is too smooth to allow lubrication. • The O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • The O-ring has a pitted or cracked surface, and is often flattened on both sides. Caused by temperature exceeding O-ring capacity. • The O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays, and air pollution. Excessive seal stretching (greater than 5%) causes similar cracking.

This sander pad is a genuine Dewalt replacement part, not generic or aftermarket. It it a Foam Rubber type pad and is compatible with clamp-on style sandpaper. It is not compatible with hook-and loop sandpaper. This sander pad has a metal backing plate with a padded sanding surface attached. The pad is complete and ready to install. This...Read more sander pad will fit the Dewalt sanders listed in the 'Compatibility' section below. It is not guaranteed to fit any other power tool models.

It is an authentic item which is supplied by the original equipment manufacturer for use with Black and Decker, DeWALT and Porter Cable sanders. The paper punch is designed to perforate a standard sandpaper when using the sander with a dust collection system. The holes will allow the dust to be picked up from the work surface. It is a hig...Read moreh-quality replacement for a damaged or a missing component that was included with a new unit. Using it does not require any tools, once the sandpaper is installed, align the corners of the paper punch with the corners of the sanding pad and press the paper punch through the sandpaper sheet. One durable plastic paper punch is included.

This Rocker switch has 2 terminals and a compact design for easy installation. This genuine DeWalt replacement part is sold individually. rnrnSwitches are commonly replaced parts in power tools. A switch handles on/off and variable speed functions. They also have a role in electric breaking; they can momentarily reverse electrical polar...Read moreity. Because switches use mechanical internals, they will degrade and wear out over time, eventually requiring replacement. Some common signs of a broken or failing switch are:rn • The tool has completely stopped functioning - it will not turn on.rn • The tool operates intermittently, requiring multiple tries to turn on, until eventually it won't turn on at all.rn • The variable speed function and electric braking aren't working properly.

This genuine cord protector, also known as a strain relief boot, is designed to safeguard the power cord where it enters your tool housing. Made from flexible, durable material, it helps prevent the cord from bending, twisting, or fraying during regular use, supporting safe and reliable performance. Small but essential, this component is ...Read morean effective replacement if the original protector is worn or damaged, helping extend the life of your tool and maintain proper cord alignment.

Genuine OEM replacement part, this item is sold individually. This screw is used in various places in all of the tools listed below The most common use for this screw is to secure plastic housings together. It has a Torx T-20 head.