CTI18GIXEIWW Hotpoint Refrigerator - Instructions

I applied some tips learned by reading other reviews. So before I started I grabbed my trusty vise grip pliers and a small screw driver. I locked onto the switch actuator, the part that the refrigerator door pushes in, with the vise grips and pulled on it just hard enough to get the screw driver inserted in the right side to push in the c ... Read more atch clip so the switch could be pulled out further each time the catch clip was depressed to the next detent. Then I used the screw driver on the left site to encourage the switch past the detents on the left and very quickly the switch was out of the mount. The wires from the refrigerator pulled out with the old switch. I unplugged the old switch from the wires and plugged in the new switch and shoved the new switch back into the mount, wiggled it a couple of times to make sure it was secure and the job was done. Once I applied the vise gripes at first, the whole job took less than a minute.

First, I removed the old gasket by ripping it out of front,

Second, I cleansed the rust (no idea how that get there, maybe it's a cheap fridge)

Third, I took some boiling water from the water boiler and dip the new gasket in it to "smooth" out the gasket and make it more "pliable" (really, it didn't seem like much h ... Read more appened, nonetheless, I did it to make sure I don't have to struggle if it comes to that)

Forth, I slap the new gasket in the top corner (inner edge closes to the fridge) and work across then down. But somehow after everything is accomplished, the gasket at the bottom appears bulged so I re-did it from the bottom up. and double checked on the firmness by checking with a flash light w/ the fridge closed (I made sure I did this near night time lol)

Lastly, I did love to thank PartSelect for shipping it out so quick. I ordered on Sunday, they shipped it on Monday and I received it on Tuesday morning at work. Incredible speedy service that even RadioShack overnight service took 3 "overnights" to recieve.

Removed the back cover of freezer to acess the coil. Turned the timer to defrost and checked the voltage across the heater. Didn't have any. Stayed on the common side of heater and measured on both sides of thermostat and one side didn't have any voltage. Shorted the thermostat wires together and heater started working.

We took the old seals off, T\they really just peal off, and replaced with the new ones.We were not really sure how they went on, because there really was no instructions with the seals, but we figured it out. After we really figured it out and got started, it was pretty easy. The only instructions that come with it is how to prep the seal ... Read more s before they go on.

Poped out with screwdriver the old swithch and unplugged the two wires. Plugged in the wires to the new swithch and pushed it back in the hole where the old switch was before.

I discovered the ice bucket missing from my rental unit at the beach. I was able to go online with my Blackberry, easily navigate your website using the model number to look up the part information , order it, and have it in place for the next renter.
Without access to a friendly user website, I would have faced considerable delay ... Read more in getting this part.

While the switch did last for 9 years, the design is poor due to the failure mode. The failure should be to fail off or not able to turn on the lights which would be inconvenient but would not warm the refrigerator contents. Arcing at the contacts eventually caused the switch to "weld" closed. It is not obvious that this is occurring s ... Read more o it took some time to recognize why the temp inside the ref was high while the freezer was OK. Replacing the switch was easy once it was recognized as the problem. All that was required to replace the switch was to remove the screws holding a fiber cover and then pulling off the aluminum cap which covered the switches. Unplug the switch an squeeze the keeper on the switch to release it and pull down. Pop the replacement switch in place and plug the wires harness back in. All in all it took much less time to replace than it has to write this up. T Pope

The existing light switch was very hard to remove. I ended up having to grab it with a pair of pliers and pull it out. Once it was out, it was very easy to put in the replacement and it seems to be working fine.

as described, I used a thin screwdriver to wedge in and pull down existing, broken switch. I was able to pull it down about a 1/4 inch, but wasn't quit able to disegage it until I gripped it with pliers. I then pulled it out, unplugged the old switch, plugged in the new switch, and carefully tucked the wires back into the fridge and snapp ... Read more ed the new switch into place.

10 minutes total.

Unplugged frige, removed top shelf, pulled broken fan blade off. Replaced with fan blade just purchased from PartSelect. Very simple repair. Orderd and recieved the right part.

Just removed the old gasket at one corner with screwdriver and pulled the rest off. Matched the gasket with the strip on the frig. and pushed it in all around. Works good.

the new gasket did not appear to exactly match the old one but it did seem like to correct size, and that it should work. I removed the old and worked the new one into the receiver bar with some good old thumb pressure. the door does not 'suck' closed but it seems to be forming around the frame and I do not feel any loss of cold air. A ... Read more ll in all a simple process from picking up the phone to completion.....hopefully saved me the cost of a new fridge for a few more years?????

I placed the new part on the end of the freezer door guard and firmly pushed it in until it 'clicked'. Easy as pie! The more difficult part was to remove the broken off part inside the opening of the freezer door hwere the new bar end was to be inserted. I finally used thin nose pliers to reach in and grab the broken off part.

Found the part I needed in only a few minutes on the website and ordered it in less than 5 minutes. The part came within 2 days and I simply removed 2 screwes from the old part and installed the new part and replaced the 2 screws , the easiest repair job that I have ever done in my home. Thanks

Start at the inside top corner and slowly work across the top, pushing with thumbs so that you feel it fitting into the groove. Go inch by inch. No speeding on this one. The gasket was so well packed that there were no folds or kinks, so no heating was necessary.