CT2510 Shindaiwa Cultivator - Overview

The Primer Pump, aka the Pump Bulb, is a clear, individually sold, plastic part, sourced from the original equipment manufacturer. It has an Outer Diameter of 0.616 Inches, 15.66mm and is 0.558 Inches and 14.19mm in height. This part is used to pump fuel from the tank to the carburator and is rated Easy to install. This part installs on...Read moreto the primer assembly. If the part dries out or starts leaking that means it is broken (likely due to fatigue or general wear) and must be replaced. Check the model number to ensure you are choosing the right part.

This OEM Fuel Filter is a white and silver, steel part, sold individually. It requires a pair of pliers to install and is ranked as Easy to repair by our customers. This part attaches inside of the fuel tank, and is used to clean the fuel of debris. This part should be changed regularly as part of good engine maintenance. If the engine ...Read moresounds like it is not getting enough fuel or is underperforming, remove the filter to heck for a blockage. If there is a blockage or the part is leaking, then it likely needs a replacement.

This individually sold fuel gasket is designed for use with handheld lawn and garden equipment and is the seal for the gas cap. This gasket is a genuine OEM part made of a composite material and will eventually become brittle because it interacts with gas and oil, meaning it will need replacing before it becomes debris in the fuel tank. T...Read morehis gasket not only prevents debris from entering the fuel tank, but it also prevents any leaks. To replace, simply unscrew your gas cap and remove the old gasket from the cap, and then replace it with the new.

The Recoil Starter Assembly, aka the Recoil Assembly, is a kit that includes the pulley, a return spring, the starter cord, and the pawls which engage the flywheel to turn over the engine. The components of this assembly are constructed of steel and plastic. The kit can be installed with a screwdriver and is rated as "Easy" to install...Read more (Tip: line all the parts up to install). This kit starts the engine, and you will know it is broken if the pull cord will not retract, or the engine is not engaging after it is pulled. The rope may also break. When the part breaks due to fatigue or general wear, it must be replaced. The part attaches on top of the engine where the flywheel is located.

This OEM metal washer is commonly used on a variety of different small engine/lawn equipment models and is sold individually. This washer is used to help evenly distribute pressure from the securing bolt or screw with the cylinder cover, to reduce any effects of vibration from the engine. If the connection between the securing fastener be...Read morecomes loose, or if you are replacing the fastener itself, it is recommended that you replace this washer as well.

This OEM Clip is a silver, steel part, which is sold individually. The part secures the fuel line to the fuel filter and is rated as Easy to install. You will know you need a new one if there is a leak around the hose where this clip is used to secure it, or if the fuel line detaches.

This air purge body assembly is a genuine OEM component. It is specially designed for Echo and Shindaiwa handheld lawn and garden equipment. By pressing on the purge bulb, it will force fuel into the fuel line from the fuel tank into the carburetor. Once the carburetor is full of fuel, the excess fuel will be purged back into the tank in ...Read morethe fuel return line. At some time the primer will lose its elasticity or crack and need to be replaced. It is a complete assembly which includes the plastic body housing and the rubber bulb. To ensure the correct installation of the new part, refer to the diagrams of your specific model. You will need a screwdriver to remove the old assembly and connect the new one.

This nickel spark plug is used in the ignition system of your lawn equipment and is located at the top or side of the engine cylinder. It has a 10mm thread diameter, 1.0mm thread pitch, 16mm hex size, and a 12.7mm reach. It creates the spark needed to ignite the air-fuel mixture for engine power. A broken spark plug may have a cracked ins...Read moreulator, worn electrode, or heavy deposits, resulting in engine issues like misfires or rough idling. To replace it, disconnect the spark plug wire and use a wrench or socket to remove the plug. This OEM-verified spark plug is sold individually.

This genuine Primer Cover, or Primer Pump Cover, is a silver, individually sold, steel part with dimensions of around 1x1 inch. This part is installed using a screwdriver, and is rated as Easy to install by our customers. This part secures the plastic primer bulb to the air purge body assembly, and must be replaced if damaged or bent.

This is a genuine manufacturer sourced replacement washer that is designed for use with Shindaiwa and Echo handheld lawn and garden equipment. It helps to distribute the pressure evenly between two connected parts, for proper application please make sure to check appropriate diagrams of your unit. This part is made from durable metal and it is sold individually.

This is an original replacement part manufactured for use with outdoor power equipment. The special screw is used with several types of equipment and the screw may have multiple applications. This fuel pump cover screw is used to secure the primer cover to the air purge body and fuel pump body. The fuel pump screw is available as an individual replacement part, please see model diagram for part location and usage.

This Foam Air Filter is a yellow, foam part, used to filter out contaminents from entering the engine. It lays on top of the main air filter, is rated as "Easy" to install, and requires a screw driver . If your filter is dirty and discolored then it has worn out, and the part should be replaced. Refer to your make, model and diagram to ensure this air filter is correct for your machine.