Models > CSG7000CAB

CSG7000CAB Maytag Cooktop - Overview

Sections of the CSG7000CAB

[Viewing 3 of 3]
Keep searches simple, eg. "belt" or "pump".
Burner Head Cap with Spark Electrode – Part Number: WP3412D024-09
Burner Head Cap with Spark Electrode
★★★★★
★★★★★
(16)
PartSelect #: PS11741732
Manufacturer #: WP3412D024-09
The burner head cap with spark electrode directs the gas to the front and back burner heads and will equally distribute the gas across cooking areas. This part can help the following symptoms: if your...
$63.05
  In Stock
Screw – Part Number: W11233072
Screw
★★★★★
★★★★★
(6)
PartSelect #: PS12349731
Manufacturer #: W11233072
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$19.99
  In Stock
Spark Module - Surface Burners – Part Number: 12001596
Spark Module - Surface Burners
★★★★★
★★★★★
(10)
PartSelect #: PS2003170
Manufacturer #: 12001596
This part may differ in appearance, but functions same as original part. : This part sends enough current to the igniter to create a spark to the bottom of the burner cap.
$60.64
  In Stock
Igniter Wire – Part Number: 5111A360-60
Igniter Wire
PartSelect #: PS2046712
Manufacturer #: 5111A360-60
This igniter wire is twenty-eight inches long.   No Longer Available
Screw – Part Number: WPW10253196
Screw
PartSelect #: PS11751203
Manufacturer #: WPW10253196
Sold individually. This screw is half of an inch long. It is made of metal and it is intended for use with some Maytag brand ranges.
$3.96
  In Stock
Seal Tape – Part Number: 12400041
Seal Tape
PartSelect #: PS1573896
Manufacturer #: 12400041
This piece of adhesive seal tape is eighty-nine inches long. It is made of black rubber and has a white backing that peels off easily. This seal tape is designed to fit around the drip pans of your appliance.   No Longer Available
Burner Grate – Part Number: 74003166
Burner Grate
PartSelect #: PS2081327
Manufacturer #: 74003166
  No Longer Available
Surface Burner Knob – Part Number: 74001299
Surface Burner Knob
PartSelect #: PS2080300
Manufacturer #: 74001299
Sold individually. This knob accepts a D-shaped shaft.   No Longer Available
Burner Switch – Part Number: WP7403P367-60
Burner Switch
PartSelect #: PS11744495
Manufacturer #: WP7403P367-60
Order quantity required.
$68.36
  In Stock
Drip Bowl – Part Number: 3424F002-90
Drip Bowl
PartSelect #: PS2037688
Manufacturer #: 3424F002-90
  No Longer Available
Drip Bowl - Black - 8 Inch – Part Number: WP3424F005-90
Drip Bowl - Black - 8 Inch
PartSelect #: PS11741739
Manufacturer #: WP3424F005-90
Sold individually.   No Longer Available
REGULATOR – Part Number: W11170853
REGULATOR
PartSelect #: PS12348157
Manufacturer #: W11170853
$193.31
  In Stock

Questions And Answers for CSG7000CAB

Be the first to ask our experts a question about this model!

Common Symptoms of the CSG7000CAB

[Viewing 4 of 4]
Will Not Start
Fixed by
these parts
Show All
Gas igniter glows, but will not light
Fixed by
these parts
Show All
Element will not heat
Fixed by
these parts
Show All
Gas smell
Fixed by
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Burner wouldn't start
Make a quarter turn counterclockwise, disengage a burner head, disconnect 2 wires, connect to a new head, install turn clockwise.

That's it!
Parts Used:
Burner Head Cap with Spark Electrode
  • Yury from Brooklyn, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
35 of 48 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No spark at top burners, first one then eventually all 4.
Most of the repair time was spent researching the problem online, locating the spark module inside the range, and selecting the part online. Installation was easy. Key troubleshooting info for me was, if there is no clicking, the spark unit is probably worn-out. I traced the ignition wires from the burners down to the spark module, located inside a 2x3" metal housing next to the bottom drawer. I removed 2 screws and out it came. The replacement unit pictured on the PartSelect site was not identical to the original but had the same number of contacts. I ordered the part and it arrived a few days later. The old connectors slipped easily onto the new pins, and I screwed the new unit into the range using the new metal housing. All 4 burners now spark up quickly, and we saved at least $100 on a service call. It was well worth the time and effort -- thanks!
Parts Used:
Spark Module - Surface Burners
  • jonathan from Bryson City, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
29 of 34 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burners would not ignite
Pulled the stove out from the wall. Removed the left side of the stove. Removed the wires from the old igniter. Modified four of the wire ends with the proper size spade connectors (supplied with the new part). Reinstalled the wires onto the new part. Tested the burners. Reinstalled the stove side. Moved the stove back into position.
Parts Used:
Spark Module - Surface Burners
  • Craig from Sequim, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
16 of 20 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!