CSG-6700 (Type 1E) Echo Chop Saw - Overview

This a a genuine OEM replacement check valve for your small engine. It is also known as a fuel tank vent. You may need to replace this part if you are noticing debris or dirty oil in the reservoir. Make sure the engine is cool before you begin this repair, and remove the wire and boot from the spark plug to prevent the engine from starting up.

This flanged hex nut is a genuine OEM steel fastener specifically designed for use in chainsaws and chop saws, serving the purpose of securing various components in these outdoor power equipment devices. It features a flange base that acts as a built-in washer for extra stability and security. The hex nut has a diameter of 6mm, and its th...Read morereaded shaft has a pitch of 20, ensuring a secure and reliable connection. Over time, the bolt can be susceptible to corrosion, cracks, or worn threads, which may result in the loosening or detachment of the connected parts. Detectable signs of such issues include excessive noise, vibrations, and equipment instability. To address this, it is recommended to inspect all bolts within your equipment and replace any that are no longer functioning properly. To replace the bolt, simply use a wrench or socket to loosen and remove the old one, position the new bolt on the mounting surface, and securely tighten it until the flange is flush against the surface. Please note that each flanged hex nut is sold individually.

The Fuel Filter is a white and silver, individually sold, steel part. It reuires pliers to install and its installation is rated as Easy. The part attaches inside of the fuel tank and is used to clean the fuel of debris. It should be changed regularly. Check your owners manual for the recommended replacement schedule for your engine. ...Read moreIf the fuel is leaking or their is a blockage, you will know the part is broken and will likely need to be replaced. To check for small leaks, feel around for dampness and the smell of fuel.

This is a genuine OEM sourced replacement part designed for use with Echo blowers/trimmers. This is a standard hardware which has multiple applications based on your unit. Please refer to diagrams for proper application. This screw is made out of metal and it is sold individually. To remove or install this screw you would need a screwdriver.

This spark plug wire, also known as a spark plug coil or spark plug cap coil, is compatible with various makes and models of hand-held outdoor power equipment and is sold individually. This wire is installed within the spark plug boot and attaches to the spark plug for the ignition of your equipment. The spark plug wire is often exposed t...Read moreo extreme heat and excessive vibrations, so through normal wear and tear, it will likely break down. If your equipment is having difficulty starting or has general performance issues, the wire may be the reason why. To replace this wire, make sure your equipment is off before removing the wire and boot from the spark plug. Remove the boot from the wire and install the new wire within the boot before re-installing the boot back to the spark plug.

This OEM metal washer is commonly used on a variety of different small engine/lawn equipment models and is sold individually. This washer is used to help evenly distribute pressure from the securing bolt or screw with the cylinder cover, to reduce any effects of vibration from the engine. If the connection between the securing fastener be...Read morecomes loose, or if you are replacing the fastener itself, it is recommended that you replace this washer as well.

This replacement screw is specially designed for use with Echo handheld lawn and garden equipment. It is a high quality OEM sourced item, not an aftermarket imitation. This screw is a standard hardware which has multiple uses depending on the equipment. Please note, this hex socket head screw is sold individually.

This replacement part is an authentic OEM screw designed for use with blowers and string trimmers. This is a standard hardware which has multiple uses based on equipment. Please refer to diagrams for proper application. This screw is made out of metal and it is sold individually. To secure or loosen this screw you would need a phillips head screwdriver.

Genuine OEM replacement part, this item is sold individually. The Vent Cover is installed on the vent tube on the carburetors for the outdoor products listed below. After the Vent Hood is installed on the vent line, the the Fuel Tank vent is attached to the Vent Hood.

This spark plug boot is an authentic OEM supplied replacement part, not an aftermarket equivalent. This rubber cap helps is used to connect the spark plug to the armature-magneto. Over time rubber material can dry out and crack requiring replacement. Please note, this part is sold individually.

This is an original Echo replacement part manufactured for use with outdoor power equipment. This special screw includes a washer and can be used with either flat or phillips head drivers. The screw has different applications, please see model diagram for part location and use. The screw is sold individually.