CS980ST6SS General Electric Range - Instructions

Slide the rang out to access the 240V plug & unplugging it. Removed the sheetmetal cover from the rear of the range to access the slip on wire plugs to prevent damaging the insulation. The insulation would be damaged if pulling them through the opening in the oven wall with the plugs attached to the element. Removed the racks from the oven. Unscrewed the retaining screws holding the element to the rear wall of the oven, lifted damaged element out and reversed the process for instillation. Perfect opportunity to clean underneath and behind the range.

Disconnect stove electrical connection. Removed 2 bolts common to the upper stove top cover. Disconnected 4 wires from burner element along with 2 retaining clips.
Removed burner element and replaced with new element. Reinstalled 4 wires and 2 retaining clips. Lowered stove top cover and reinstalled 2 bolts. Connect stove electrical to wall outlet. Turn on burner element and verify that it works.

PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.

Pull out wires & replace element by putting wires back in then tighten...done!!!!

Used nut driver and removed the 4 nuts holding the broiler. Pulled electrical wires of old broiler Received new unit and it was just as easy to replace. Thank you for assistance.

First, disconnect electrical power to the stove by turning the main fuse to the off position. Confirm that there is no electrical power in the stove. The ceramic top is held by 10 screws that are closest to the ceramic surface. Other screws hold other parts of the stove and not need to be touched when opening the stove. Once the ceramic surface is off there is access to the burners and the various lights and switches. It is important to determine whether it is the burner that is defective or the switch. Inasmuch as the switch has many moving parts, the switch is more likely to be the defective part. Check the switch by gaining access to the switch connections. There is a metal frame held by two screws on each side in the outside of the stove (same area where the initial 10 screws were removed to separate the ceramic surface). Remove these screws and flip the switch assembly so all the wires and cables are accessible. I checked the switch with a continuity tester and by trial and error determined that there were two connections that in all the remainder three switches had continuity when the switch was in the on position while the suspect switch did not. Replaced the suspect switch by pulling the wires and replacing them in identical positions in the new switch (a smartphone camera became very useful to remind me were exactly each cable's connection was). Restore power by turning the fuse to the on position. Check that the burner lights up. If not, change the burner as well. Same simple procedure of disconnecting and connecting cables to the burner). Make sure to disconnect power before working on the burner. Replace the screws that hold the switch assembly. Replace the ceramic top. Replace the screws. Set stove back in its hole. Reset fuse. Total time: 35 mins. Total cost: Approx $25.00 (switch + delivery). Quoted repair by local appliance repair service: $487.50. No contest. Next project is to fix a leaky water dispenser in the refrigerator.

Turned off juice
Pulled stove from wall
Unscrewed 2 screws to loosen range top
Lifted n propped top
Unplugged 4 wires
Unscrewed burner assembly
Installed burner-reversed steps to reassemble

Easy

Move range out from wall,unplug power supply,remove two screws from back wall of lower oven element unplug two wires,discard burned element.Install new element,plug two wires in,fasten two screws. Done

The unit has two spring clips that hold it in place. Also two screws that hold the element to the clips. It comes apart ok but doesn't go back as easy. I didn't remove the top as there was room to work from under it.

My daughter held the top down against a wooden dowl i was using as a prop rod . My wife held the unit in place . I finally got the clips back on and the screws back in . Centered the unit , transfered the wires , and it works perfect . Only three people and 30 min.

Thank you PartSelect for all your help !!

after removing element.I order part. part was inserted without problems . It was correct fit. I am now baking again. Thank you the quick services on the order.

Remove and replaced water valve, seems to have fixed the problem

Use a 1/4" nutdriver and remove the screws that are on the bottom corners of the range top.Prop up the range top high enough for ease of using 1/4" nut driver. Take a picture of the wiring for future reference on re-installing wiring. Note arrow location on burner and remove 1/4" screws holding the clamps to the burner in place and place to the side for re-install on new burner.Remove wiring off old burner.Hold new burner in place with arrow location in previous location and notice holes where clamps will go. Screw clamps on burner using original screws and snap in mounting slots on stove.Re-install wiring.Lower range top and re install 2 screws , 1 in each corner under range top. Test for proper operation and enjoy!

First I found the model number, but it's parts were under a different number. So I ordered what I thought was the right oven element, but it wasnt right . My husband couldnt get it to fit . Well he finaly found the right part number so we could order the right part. We returned the wrong part and got the right element. It went in perfectly and the oven is working just fine now. Remember to always look up the part number you need and then order it.

Was a piece of cake removed 2 screws, pulled element out. Pulled the wires ooff the old unit and put them on new unit and screwed it back in.