This flanged hex nut is a genuine OEM steel fastener specifically designed for use in chainsaws and chop saws, serving the purpose of securing various components in these outdoor power equipment devices. It features a flange base that acts as a built-in washer for extra stability and security. The hex nut has a diameter of 6mm, and its th...Read morereaded shaft has a pitch of 20, ensuring a secure and reliable connection. Over time, the bolt can be susceptible to corrosion, cracks, or worn threads, which may result in the loosening or detachment of the connected parts. Detectable signs of such issues include excessive noise, vibrations, and equipment instability. To address this, it is recommended to inspect all bolts within your equipment and replace any that are no longer functioning properly. To replace the bolt, simply use a wrench or socket to loosen and remove the old one, position the new bolt on the mounting surface, and securely tighten it until the flange is flush against the surface. Please note that each flanged hex nut is sold individually.
This replacement tensioner is specially designed for use with Echo pole pruners/chainsaws. This part is a crucial component of chain tensioning mechanism. If the bar doesn't adjust when you turn the tension screw usually the tensioner pin or the adjustment bolt is worn or damaged. This part is made out of metal and it is sold individually.
This OEM nut is a 5mm, gold, metal nut, which is sold individually. It can be installed with a Wrench or Socket and Torque Wrench by torquing to the manufacturer specifications. This nut is used to secure another part in place, and should be replaced if damaged due to fatigue (such as damaged threads or rounded ends).
This nut can have v...Read morearious uses on various equipment, and as such the difficulty of the installation can vary, but generally this is an easy repair.
This spark plug wire, also known as a spark plug coil or spark plug cap coil, is compatible with various makes and models of hand-held outdoor power equipment and is sold individually. This wire is installed within the spark plug boot and attaches to the spark plug for the ignition of your equipment. The spark plug wire is often exposed t...Read moreo extreme heat and excessive vibrations, so through normal wear and tear, it will likely break down. If your equipment is having difficulty starting or has general performance issues, the wire may be the reason why. To replace this wire, make sure your equipment is off before removing the wire and boot from the spark plug. Remove the boot from the wire and install the new wire within the boot before re-installing the boot back to the spark plug.
This OEM metal washer is commonly used on a variety of different small engine/lawn equipment models and is sold individually. This washer is used to help evenly distribute pressure from the securing bolt or screw with the cylinder cover, to reduce any effects of vibration from the engine. If the connection between the securing fastener be...Read morecomes loose, or if you are replacing the fastener itself, it is recommended that you replace this washer as well.
This replacement screw is specially designed for use with Echo handheld lawn and garden equipment. It is a high quality OEM sourced item, not an aftermarket imitation. This screw is a standard hardware which has multiple uses depending on the equipment. Please note, this hex socket head screw is sold individually.
This spark plug boot is an authentic OEM supplied replacement part, not an aftermarket equivalent. This rubber cap helps is used to connect the spark plug to the armature-magneto. Over time rubber material can dry out and crack requiring replacement. Please note, this part is sold individually.
This is an original Echo replacement part manufactured for use with outdoor power equipment. This special screw includes a washer and can be used with either flat or phillips head drivers. The screw has different applications, please see model diagram for part location and use. The screw is sold individually.
It is a genuine OEM approved replacement item specially designed for use with Echo gas powered handheld tools. This replacement fuel-strainer/filter fits inside of the fuel tank. The purpose of this item is to filter out dirt and debris from contaminating engines. Over time fuel filter will get clogged and restrict the fuel getting to the...Read more carburetor. At this point filter should be replaced. This filter consists of a metal body with fabric filter material and it is sold individually.
This manufacturer sourced replacement part is designed for use with Shindaiwa and Echo handheld lawn and garden equipment. A lock nut is a type of nut that resists loosening when properly threaded onto a bolt. This is a standard hardware which will has multiple applications depending on your equipment. This lock nut is made from high quality metal and it is sold individually.
The intake gasket is a genuine item that is supplied by the original equipment manufacturer for use with Echo chainsaws and backpack blowers. It fits between the air cleaner case assembly and the carburetor. It is made of a thin flexible material that can break easily. When replacing this item a screwdriver may be required. It is priced individually.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Saw would run with Fuel Sprayed into Carb. & quit, not pumping Fuel, Rebuild CRB.
2 of 3 peoplefound this instruction helpful.
Gerald from Saratoga, WY
A Bit Difficult
More than 2 hours
Pliers, Screw drivers, Socket set
Problem was how to remove Carb. from a 37 year old chainsaw and not destroy Carb. Housing in the process. The John Deere 80EV chainsaw was made by Echo and was a CS750EVL model in 1978-1985. The Carb. is in a plastic housing with access holes for fuel line, choke rod, throttle linkage, high speed & low speed needle adjustments and Idle
... Read moreadjusting screw. After removing the obvious, the high and low speed needles were to long to clear the housing. Had to remove the rubber grommet seal that closes the stop of the plastic housing and gives access to the top slots in the high & low speed mixture adjustments. That is the "secret" in how to get to the carb. so you can rebuild. The carb. rebuild is the easy part.