CS-3500 Echo Chainsaw - Overview

This part is the replacement stud for your chainsaw. It is approximately 1 ¼ inches long and is black in color. The stud secures the chain bar to the chainsaw. It the stud is damaged or missing, it can become a safety hazard, and will need to be replaced. This part is sold individually and is an OEM part sourced directly from the manufacturer.

This genuine fuel clip is a silver, metal, individually sold part. It can be installed with pliers and is rated as Easy to install by customers. This part attaches to the fuel filter to secure the fuel line ot the fuel filter. If broken, likely due to fatigue, there may be a fuel leak. If damaged or missing, the part should be replaced. ...Read moreRefer to your owners manual or model number to ensure you are choosing the correct part.

This is a genuine OEM replacement part, it is sold individually. It is used in various places on the models shown below.. It is mainly use to secure parts such as Guide Bar Covers, Sprocket Guards etc.

Genuine OEM replacement part, this part is sold individually. The Bevel Gear is part of the chain tensioning assembly of the chainsaws listed below. This part aid in loosening and tightening the chain on the chain bar.

This is a genuine manufacturer approved replacement part designed for use with chainsaws. This part is an essential part of chain tensioner mechanism. When replacing this part you will need a screwdriver. It is made out of metal and it is sold individually.

This is an Authentic Part sourced from Original Manufacturer. This part is made out of Metal and it is Sold Individually. If the chainsaw bar doesn't adjust when you turn the tension screw usually the tension gear/pin or the adjustment bolt is worn or damaged.

Used in over 150 models of outdoor power equipment, this clip is commonly used to clip fuel lines or other hoses/tubes in place. It is sold individually, not as part of a kit or assembly, made of metal, and is silver in color. When this clip becomes damaged or worn, it can no longer support the fuel line, which may cause a fuel leak and...Read more/or smell. This wear will occur as part of regular use of your equipment. To complete this repair, you will need a wrench, screwdriver, and pliers. It is found in a variety of locations depending on your model; please refer to your owners manual for the exact location. Customers rated this repair as Easy.

This screw is supplied directly from original equipment manufacturer for use with Shindaiwa and Echo power equipment/tools. This screw is a standard hardware that has multiple uses depending on your model. Please make sure to check appropriate diagrams for correct location and application for this screw. It is made out of metal and it is sold individually. To secure/loosen this screw you would need a screwdriver.

This spark plug wire, also known as a spark plug coil or spark plug cap coil, is compatible with various makes and models of hand-held outdoor power equipment and is sold individually. This wire is installed within the spark plug boot and attaches to the spark plug for the ignition of your equipment. The spark plug wire is often exposed t...Read moreo extreme heat and excessive vibrations, so through normal wear and tear, it will likely break down. If your equipment is having difficulty starting or has general performance issues, the wire may be the reason why. To replace this wire, make sure your equipment is off before removing the wire and boot from the spark plug. Remove the boot from the wire and install the new wire within the boot before re-installing the boot back to the spark plug.

This clutch washer, also known as a circular washer, is authentic manufacturer replacement part which is positioned on the crankshaft between the clutch drum and the engine. It is a circular metal ring with an outer diameter of 1 inch. The clutch engages with the clutch drum and sprocket to allow the chain to rotate when the engine accele...Read morerates. Over time, the clutch washer can wear out or become damaged due to normal aging, inadequate lubrication, or exposure to excessive heat. If the clutch washer is faulty, the chain will not engage or rotate properly, resulting in a loss of cutting power and poor engine performance. To access the clutch washer first remove the chain cover and bar, and then loosen and remove the clutch assembly. Carefully remove the old clutch washer and position the new one in its place. Ensure that it is properly aligned before reassembling the clutch assembly, chain, and bar.

This OEM metal washer is commonly used on a variety of different small engine/lawn equipment models and is sold individually. This washer is used to help evenly distribute pressure from the securing bolt or screw with the cylinder cover, to reduce any effects of vibration from the engine. If the connection between the securing fastener be...Read morecomes loose, or if you are replacing the fastener itself, it is recommended that you replace this washer as well.

This replacement spark plug cap is a genuine OEM sourced item designed for use on handheld lawn and garden equipment. It is used to insulate the plug and wire terminal. Over time rubber material can dry out and crack requiring replacement. Please note, this item is sold individually.