Models
>
CRG560A
CRG560A Maytag Range - Overview
Sections of the CRG560A
[Viewing 4 of 4]
Keep searches simple, eg. "belt" or "pump".
Flat Style Oven Igniter Kit
PartSelect #: PS1573892
Manufacturer #: 12400035
The flat style oven igniter kit is used in gas ovens and ranges. It is what provides the heat needed to open the gas valve, and it ignites fuel for the burner assembly. This part can be used for both ...
$57.79
In Stock
Burner Head Cap with Spark Electrode
PartSelect #: PS11741732
Manufacturer #: WP3412D024-09
The burner head cap with spark electrode directs the gas to the front and back burner heads and will equally distribute the gas across cooking areas. This part can help the following symptoms: if your...
$67.94
In Stock
Screw - 10-16 x 1
PartSelect #: PS11741409
Manufacturer #: WP3387230
This screw is sold individually.
$7.95
In Stock
Oven Door Spring
PartSelect #: PS11744749
Manufacturer #: WP7803P058-60
The oven door springs create tension which allows the door to open and close with ease. This spring can be used on either the left or right side of your oven, is made completely of metal, and is appro...
$17.05
In Stock
Spark Module - Surface Burners
PartSelect #: PS2003170
Manufacturer #: 12001596
This part may differ in appearance, but functions same as original part. : This part sends enough current to the igniter to create a spark to the bottom of the burner cap.
$61.76
In Stock
Frame Screw
PartSelect #: PS11743908
Manufacturer #: WP7101P126-60
Sold Individually.
$7.76
In Stock
Stand Mixer Screw
PartSelect #: PS11742292
Manufacturer #: WP4159193
This screw is sold individually.
$8.63
In Stock
Screw - 6-32 x 5/16
PartSelect #: PS11744050
Manufacturer #: WP74004005
This screw is well under an inch long, and is made of metal.
$5.36
Special Order
Safety Valve - just over four inches long
PartSelect #: PS11744552
Manufacturer #: WP7501P133-60
This safety valve ensures that no gas is released until the igniter has received the proper voltage needed to ignite the gas range. This safety valve has an amperage range of 3.3 to 3.6 amps. The valv...
$285.41
In Stock
Oven Thermostat Kit
PartSelect #: PS2006880
Manufacturer #: 12400034
This oven thermostat kit is to be used with gas oven models with a flat ignitor. Many thermostats do look similar. The knob has been updated by the manufacturer and may not look the same as the original.
No Longer Available
Screw
PartSelect #: PS11751203
Manufacturer #: WPW10253196
Sold individually. This screw is half of an inch long. It is made of metal and it is intended for use with some Maytag brand ranges.
$4.68
Special Order
Questions And Answers for CRG560A
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the CRG560A
[Viewing 9 of 9]Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Little to no heat when baking
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Gas smell
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Little to no heat when broiling
Fixed by
these parts
these parts
Show All
Oven is too hot
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven would not work but the Broiler did
The oven had been working intermittently for a while and after repeated threats of starvation from my spouse I finally took a look even though it was summer and the grill was working fine. The Igniter would glow red when the oven was turned on but the gas would not flow to it no matter what the temperature setting. I searched online and f
... Read more
ound this site that explained it was possible for the igniter to glow but if it was not drawing the correct amperage (because its resistance was too high) then the main brain would not allow the gas valve to open. So I took a look at the broiler and it had the same igniter. I measure the resistance of both of them and the oven igniters resistance was higher (don't rememeber the reading) then I moved the Igniter from the broiler to the oven and the oven worked from there it was just a matter of ordering the part. End of story except for I am still doing all the cooking on the barbecue outside.
Read less
Parts Used:
-
James from Ferndale, MI
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers, Socket set
336 of 370 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven would'nt light
In most cases if your oven won't light or takes a long time to light you may have a bad igniter even if it glows. To check the igniter use a voltmeter to check for 120 A/C volts going to the igniter and3.5 A/C volts going between the ingniter and the gas valve. My bad ingniter glowed but had only only 3.0 A/C volts going to the gas valve
... Read more
for the oven. The new igniter took only 45 minutes to install and supply's 3.6 A/C volts to the gas valve and the oven works fine.
Read less
Parts Used:
-
Charles from Charlestown, RI
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
130 of 141 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven failed to light
My son replaced the broiler igniter this spring, so I had a clue as to what was required. This was even easier and since I had back surgery recently & my husband was out of town that was a giant plus!
I unplugged the oven, removed the oven door, found the release latch and removed the oven floor. I then removed the 2 screws ... Read more that held the igniter in place (I received this stove used and the igniter had evidently been replaced before as it was the same shorter version included in the kit). I pulled the igniter out then removed some insulation and tugged the connector out of the oven floor. I disconnected the igniter and plugged the new one in. I then replaced the connector in the floor, attached the igniter with the screws, replaced the insulation and did a test run (plugged in the oven & turned it on). That was successful so I put the floor back in and put the door back on.
Ta-Dah!
I unplugged the oven, removed the oven door, found the release latch and removed the oven floor. I then removed the 2 screws ... Read more that held the igniter in place (I received this stove used and the igniter had evidently been replaced before as it was the same shorter version included in the kit). I pulled the igniter out then removed some insulation and tugged the connector out of the oven floor. I disconnected the igniter and plugged the new one in. I then replaced the connector in the floor, attached the igniter with the screws, replaced the insulation and did a test run (plugged in the oven & turned it on). That was successful so I put the floor back in and put the door back on.
Ta-Dah!
Read less
Parts Used:
-
Beryl from Dawsonville, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
69 of 74 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!