CPF6025VP (Type 0) Porter Cable Compressor - Overview

Frequently referred to as a Drain Plug, this Drain Valve is used to drain any condensation that has collected inside the tank to prevent the tank from rusting. It is not part of a kit or assembly, is sold individually, made of brass, is gold, and will be found at the bottom of the air tank. This part will need to be replaced when it is ...Read moreno longer able to provide a proper seal, or if it is visibly worn or damaged. You will need a wrench to complete this repair. Customers rate this repair as Easy.

Restore air pressure in a compatible oil free air compressor with this cylinder service kit, it includes a cylinder sleeve, compression ring, piston rod screw, and two sealing rings, replace worn parts when the compressor runs but makes little or no air, unplug the compressor and release all tank pressure before repair, check the model and type number before ordering.

This fan is an exact replacement part for use in air compressors and is sourced directly from the manufacturer. It is made of durable black plastic and is used to cool the compressor during operation. It is not part of a kit or assembly and is sold individually. This part is located on the end of the motor shaft and will be visibly brok...Read moreen or worn when it needs to be replaced. You will need a screwdriver, a socket set, and a drill to complete this repair. Customers rate this repair as Easy.

Sourced directly from the manufacturer, this part is an exact replacement for various air compressors. Its primary purpose is to control the airflow through the pump. This part is an assembly that includes the plate gasket and seals. When this part is malfunctioning, the tank will take longer to fill or will not be able to fill at all. I...Read moret will need to be replaced once it becomes damaged or worn. You will need a wrench set and a socket set to complete this repair. Customers rated this repair as Easy.

This is an authentic Craftsman replacement part that has been sourced from the original manufacturer to be used with air compressors. The three wire cord is encased in a durable jacket and includes terminals at the end of the wires. The cord is used to relay electricity from the outlet to the switch assembly. This item is available as an individual replacement part.

This wheel is a genuine OEM replacement part used in portable air compressors. It consists of a plastic rim and rubber tire with an outer diameter of 9.5 inches. It is held in place on the compressor axle by a shoulder bolt and nut. The wheel allows the equipment to move smoothly during use. If the tire is punctured, or the rim is damaged...Read more, the wheel will need to be replaced to restore the portability of your equipment. If the nut and bolt are worn down, it is recommended to replace them at the same time. Remove the nut and bolt that secure the wheel and pull it off the axle. Place the new wheel in position and secure it with the fasteners (sold separately). Each wheel is sold individually.

O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. rnrnThere are many causes for O-Ring failure. The most common among power tools are: • Extrusion and Nibbling - The O-ring has ragged, tattered edges. ...Read moreThese are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • Abrasion - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that it too rough, contains grit or is too smooth to allow lubrication. • Over Compression - The O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • Heat Hardening - The O-ring has a pitted or cracked surface, and is often flattened on both sides. Caused by temperature exceeding o-ring capacity. • Weather/Ozone Cracking - The O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching (greater that 5%) causes similar cracking.

O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-Ring failure. The most common among power tools are: • Extrusion and Nibbling • The O-ring has ragged, tattered edges. Thes...Read moree are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • Abrasion • One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that it too rough, contains grit or is too smooth to allow lubrication. • Over Compression • The O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • Heat Hardening • The O-ring has a pitted or cracked surface, and is often flattened on both sides. Caused by temperature exceeding o-ring capacity. • Weather/Ozone Cracking • The O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching (greater that 5%) causes similar cracking.

This is an authentic OEM part. The filter is used with air compressors from Porter Cable, DeVilbiss, and Black & Decker. The foam filter is used to prevent dirt and debris from entering and potentially damaging the pump. A hex driver, or screwdriver may be needed to install this item and it is sold individually.

It is a genuine manufacturer-sourced replacement screw which is specially designed for use with air compressors. This is a standard hardware which has multiple applications depending on the model of your unit, make sure to check appropriate diagrams for the correct location and use of this item. It is a high-quality hex head screw which i...Read mores made of durable metal and it is sold individually, over time the threads may wear out eventually requiring a replacement.

The gauge attaches to the pressure switch and is made of plastic and metal. It is an authentic OEM sourced item which is specially produced for use with compressors made by Porter Cable, DeVilbiss, and Black & Decker. This item is available as an individual replacement part. A wrench set may be helpful when replacing this part. This item may stop working and will need to be replaced.