COIL250 (Type 1) Porter Cable Nailer - Overview

This unthreaded trigger valve assembly is a genuine OEM assembly used in nailers. It includes the trigger valve, 1 rubber washer, and 3 roll pins. The trigger valve controls the flow of air in the tool which drives the piston and creates the nailing action. If the valve becomes stuck, the seals wear down, or the trigger breaks the nailer ...Read morewill leak air, struggle to fire, or not fire at all. Begin the repair by switching off the tool and using a push pin to remove the trigger. Remove the roll pins that secure the trigger valve and pull the trigger valve out of the housing. Insert the new valve into the housing, install the pins to hold it in place, and secure the stay pin with the washer.

O-rings are designed to contain thousands of pounds of pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. Of the many causes for O-Ring failure, the most common are: • Extrusion and Nibbling - O-ring has ragged, tattered edges. These are com...Read moremonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • Abrasion - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that is too rough, contains grit or is too smooth to allow lubrication. • Over Compression - O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • Heat Hardening - O-ring has a pitted or cracked surface, and often is flattened on both sides. Caused by temperature exceeding o-ring capacity. • Weather/Ozone Cracking - O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching causes similar cracking.

Genuine Porter Cable replacement part, this item is sold individually. This retaining Ring is used in various areas of the Pneumatic Tools listed below. In most cases it is used to secure a pin in place in the tool.

This is a Genuine OEM replacement part used on a variety of Power Tools. It allows to keep the Carrying Case closed. This part is made out of Plastic and it is Sold Individually. Included in part number 901023

This is an authentic OEM sourced component which is specially designed for Porter Cable staplers and nailers. It is an identical replacement for a missing or faulty rolled pin that was originally installed on a new unit, please make sure to check the appropriate diagrams of your model for the correct location and application of this hardw...Read moreare. Keep in mind this high-quality item is made of durable metal and is sold individually.

O-rings are designed to contain thousands of pounds of pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. Of the many causes for O-Ring failure, the most common are: • Extrusion and Nibbling - O-ring has ragged, tattered edges. These are commonly...Read more caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • Abrasion - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that is too rough, contains grit or is too smooth to allow lubrication. • Over Compression - O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • Heat Hardening - O-ring has a pitted or cracked surface, and often is flattened on both sides. Caused by temperature exceeding o-ring capacity. • Weather/Ozone Cracking - O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching causes similar cracking.

This replacement seal is an authentic OEM sourced item, it is not an aftermarket imitation. It is specially designed for use with Porter Cable staplers and nailers. This is the seal for the cylinder cap. It is made from durable composite material and it is sold individually. Replacing this item you will need a hex key also known as an allen wrench.

It is a genuine item that is sourced directly from the original equipment manufacturer for Porter Cable nailers. The rolled pin secures the restrictive trigger in the housing. If the hardware is damaged or is missing, this part will provide an identical replacement for the original component that was installed on a new unit. Check the app...Read moreropriate diagrams for your model to ensure the correct replacement procedure. Note, this high-quality rolled pin is made of durable metal and is sold as an individual item. You might need pliers and a hammer to perform this repair.

This is a genuine Porter Cable hardware which is sourced from the original manufacturer for use with nailers and staplers. It is an identical replacement for a missing or a damaged hardware that was installed on a new unit. Refer to the diagrams for your model to ensure the exact location and the correct application of this component. Thi...Read mores high-quality part is made of durable metal and is sold individually. You may need pliers to remove and secure this pin.