Models
>
CMV1100AAB
CMV1100AAB Maytag Microwave - Overview
Sections of the CMV1100AAB
[Viewing 6 of 6]Keep searches simple, eg. "belt" or "pump".
Light Bulb - 120V 25W
PartSelect #: PS11747806
Manufacturer #: WPA3073101
This light bulb is a 120 volt, 25 watt incandescent appliance light bulb with a small base screw-in that fits in a variety of appliances such as microwaves, refrigerators, freezers, cooktops, or stove...
$17.11
In Stock
Grease and Air Filter
PartSelect #: PS11742996
Manufacturer #: WP58001087
This grease and air filter is nine inches long and six and a half inches wide. It is made of metal.
$35.08
In Stock
Turntable Drive Motor
PartSelect #: PS11742994
Manufacturer #: WP58001047
This motor rotates the glass turntable in the microwave.
No Longer Available
Carbon Air Filter
PartSelect #: PS11742995
Manufacturer #: WP58001086
This carbon air filter is ten inches long and seven inches wide. It is made entirely of metal.
$31.92
In Stock
Screw
PartSelect #: PS11751203
Manufacturer #: WPW10253196
Sold individually. This screw is half of an inch long. It is made of metal and it is intended for use with some Maytag brand ranges.
$4.68
Special Order
Questions And Answers for CMV1100AAB
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the CMV1100AAB
[Viewing 2 of 2]Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Turntable on Maytag MMV5100AAW Stopped Turning
Symptom: Turntable stopped turning. Was able to remove the glass tray in the microwave and the little cam that drives the glass tray was barely turning. Control on microwave to turn the turntable on/off was working as evidenced by the cam not turning when I turned off the turntable. When I turned the cam manually, I could feel the moto
... Read more
r turn so I knew the CAM and motor shaft were not stripped.
Repair Procedure:
1) Unplug the microwave.
2) Remove the 4 screws from the bottom of the microwave while holding the bottom cover so that it does not suddenly drop. It is not very heavy so you are fine to hold it with one hand and unscrew the screws with the other. Don't drop it as it has a glass lens for your lights and two light bulbs that light up the cooktop below.
3) Swing the front of the cover down slowly. You wil notice that the back is held in by tabs that slide into the back of the microwave. The bottom cover comes off very easily with some forward motion to dislodge the tabs.
4) Now look up under the bottom of the microwave(assuming your microwave is mounted over the range like mine) and you will see the turntable motor (GEAR MOTOR) in the center.
5) Carfully remove the two wires from the motor by gently working the connectors off of the motor using neegle nose or regular pliers. Don't grab the wires as you may pull them out of the connectors. Work with the connectors on the motor terminals. You will find the job much easier to do if you also remove the wires from the light housing. This will allow you to set the bottom cover aside and will give you greater access to do the job.
NOTE: Now is a great time for you to clean the filters, filter slots, bottom cover, and the light lens. A lot of grease can accumulate on the bottom of the microwave if it is mounted over a range (like mine). If you remove the light assembly, you can clean the cover, filters, and and light lens in the sink. Make sure that you dry all components thoroughly before re-assembling.
6) Make a note of which wires go to which terminals on the motor and the lights.
7) Remove the two screws from the motor and remove it. Note that there is a little plastic insulator film, a very thin washer and a bushing associated with the motor. You will want to re-install these with the new motor. Replace the motor with the new one being careful to put the other pieces back in place as well. Note that the little black turntable cam has a tab on one side so if you want to put it out of the top, you will need to tilt it slightly.
8) With the motor and associated parts back in and secured with the two screws previously removed, re-attach the wires to the lights and motor.
9) Replace the cover and screws and you are done!
This repair is much easier than these steps would suggest but I wanted to be thorough.
I called Maytag and they refused to sell me the part because they said it was dangerous for the user to replace it - rubbish. As long as you kill the power to the microwave and confine your work to the bottom of the unit as described, you will be fine. Maytag wanted to send out a repairman at $80 just to show up. I did the entire repair myself in about 15 minutes for about $40.
Repair Procedure:
1) Unplug the microwave.
2) Remove the 4 screws from the bottom of the microwave while holding the bottom cover so that it does not suddenly drop. It is not very heavy so you are fine to hold it with one hand and unscrew the screws with the other. Don't drop it as it has a glass lens for your lights and two light bulbs that light up the cooktop below.
3) Swing the front of the cover down slowly. You wil notice that the back is held in by tabs that slide into the back of the microwave. The bottom cover comes off very easily with some forward motion to dislodge the tabs.
4) Now look up under the bottom of the microwave(assuming your microwave is mounted over the range like mine) and you will see the turntable motor (GEAR MOTOR) in the center.
5) Carfully remove the two wires from the motor by gently working the connectors off of the motor using neegle nose or regular pliers. Don't grab the wires as you may pull them out of the connectors. Work with the connectors on the motor terminals. You will find the job much easier to do if you also remove the wires from the light housing. This will allow you to set the bottom cover aside and will give you greater access to do the job.
NOTE: Now is a great time for you to clean the filters, filter slots, bottom cover, and the light lens. A lot of grease can accumulate on the bottom of the microwave if it is mounted over a range (like mine). If you remove the light assembly, you can clean the cover, filters, and and light lens in the sink. Make sure that you dry all components thoroughly before re-assembling.
6) Make a note of which wires go to which terminals on the motor and the lights.
7) Remove the two screws from the motor and remove it. Note that there is a little plastic insulator film, a very thin washer and a bushing associated with the motor. You will want to re-install these with the new motor. Replace the motor with the new one being careful to put the other pieces back in place as well. Note that the little black turntable cam has a tab on one side so if you want to put it out of the top, you will need to tilt it slightly.
8) With the motor and associated parts back in and secured with the two screws previously removed, re-attach the wires to the lights and motor.
9) Replace the cover and screws and you are done!
This repair is much easier than these steps would suggest but I wanted to be thorough.
I called Maytag and they refused to sell me the part because they said it was dangerous for the user to replace it - rubbish. As long as you kill the power to the microwave and confine your work to the bottom of the unit as described, you will be fine. Maytag wanted to send out a repairman at $80 just to show up. I did the entire repair myself in about 15 minutes for about $40.
Read less
Parts Used:
-
Tim from Oviedo, FL
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
46 of 47 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No Power to Microwave
After determined the problem on one of the websites...I received the part I needed... removed the control panel and installed the new main fuse In about 15 mins!
Parts Used:
-
John from Palos Hills, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
42 of 88 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burnt out bulb
took cover off, installed bulb.
lost the owners manual,
part select's schematics were very helpful
thanks
lost the owners manual,
part select's schematics were very helpful
thanks
Parts Used:
-
THOMAS from STOW, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
27 of 61 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!