CKS70DP2N2S1 General Electric Wall Oven - Instructions

It took a while to remove approx 30 screws to get to the blower. So my oven was sitting, torn apart while I waited on the new blower fan that I had ordered. It arrived shortly, about 5 days. When I opened the box I saw that PARTSELECT had sent me a drain pump instead of the blower fan that I had ordered. Since an oven does not require a d ... Read more rain pump and it wouldn't work to replace my broken blower fan I had to return it. I was told that I needed to send the part back in order to get a refund. After I sent their drain pump back at a cost of $13 they emailed me and said I didn't need to send the drain pump back. And they refunded me minus shipping So I had to pay shipping both ways for a part that was wrong. And I ordered it from someone else. I put the new blower fan that I had bought from another company in and replaced the 30 screws. And the oven has been working fine ever since. Thank you PARTSELECT for allowing me to tell people how you operate. They have a money back guarantee, but they don't give you back ALL your money. Thanks Again.

After opening the Oven door, I removed the glass cover to view and locate the bulb, at the inside, top front of the Oven. Removed the burnt out bulb by pulling it in a forward motion towards the front of the Oven, slid the new bulb into place and the Oven is again functional.

I used a Trox bit to remove one screw, replaced the oven sensor and reinstalled the screw. The whole project took less than 5 minutes.

Changed Fan Blower only, which cleared the Error Code F96.
Other parts have been kept as spares.

TERRIBLE!!!!!!!
FIrst part arrived broken
Second part arrived broken
Third part arrived broken
Finally on the 4th try, the part arrived and was not broken.
I will NEVER again order parts from this company.

Turn power off to oven, removed screws holding oven into cabinet, get assistance to remove oven, I used 2 dinner table chairs to set the oven on, be careful as the front of the oven is heavier than the back. Removed the back sheet metal covers, about 20 screws or so. Removed Fan motor, replaced with new fan motor, and reversed installed. ... Read more Oven works great.

I ordered the glass assembly which promptly arrived and I proceeded to unscrew the broken glass assembly and (by myself) removed it with ease. I then placed the new glass assembly and replaced the screws. It was really an easy job, I just retraced my steps from removing the broken assembly and replacing it with the new assembly. By th ... Read more e way, it was the first time I had done this.

taking the oven out of the wall the most difficult part.. once you removing the sheet metal screws....be sure to take pictures as you dis-assemble putting back together will be easier. wait for correct part. second try they sent the correct part. put back together, test before putting back into wall.. big savings by doing it yourself.

Watched a video on how to replace , had no problem remaking the repair, part was a perfect fit and had no hang up or issues

Very straight forward repair except for removal of the fan mount plate. There are 4 sheet metal screws, 2 of which are obvious and shown in the appliance diagrams, and 2 of which are neither on the appliance diagram nor obvious. These screws are beneath the motor assembly and oriented with the heads between the mounting plate and the to ... Read more p of the oven - about a 3/8 inch gap. Removal was accomplished using a 1/4 inch open end wrench strictly by feel as there is no sight line. Not all that challenging, but still a pain. On reassembly, these screws were reversed so that the head is now on the top of the plate and more accessible.

there was one screw holding it on the back wall of the oven. It was easy enough that my daughter installed it with my guidance.

Step 1, turn off circuit breaker, verify no power at the back of oven

Step 2, remove oven from wall/housing by removing 4 mounting screws, 2 on each side, just on the inside after opening the oven door...this was the most difficult part doing the repair on my own as the oven is a bit heavy...I was fortunate to have a old Workma ... Read more te 425 work bench that folds/collapses, this allowed me to slide the oven out and drop down about 2 inches...reinstalling the oven I did have to use 2x4s to shim the oven level to slide it back in, with someone to assist this would not be necessary.

Step 3, remove covers to gain access to the blower and sensor

Step 4, remove the sensor

Step 5, install new sensor

Step 6, turn on the circuit breaker

Step 7, test the oven (success, Y, turn off breaker and reassemble all covers, install the oven, secure with the 4 mounting screws, turn on circuit breaker, test one more to ensure of proper operation...N, go to step 8

Step 8, turn off circuit breaker, reinstall original sensor

Step 9, remove blower

Step 10, install new blower

Step 11, turn on circuit breaker

Step 12, test oven, problem resolved, Y, go to step 13, N, continue troubleshooting.

Step 13, turn off circuit breaker

Step 14, replace all covers and reinstall oven, secure with 4 mounting screws

Step 15, turn on circuit breaker

Step 16, test, still operating properly Y, receive hugs and kisses from wife, N, do not make eye contact with wife, take dog for a long walk.

This item worked as described. I paid more for this 'oem' probe than the generic 1 because i didn't want to chance it not working as others have reported.
- works great. tested it....snaps in, reads correctly, snaps out.

Removed screws from front of oven, placed a table under oven 2” below, places two rollers on table and pulled out the oven. Removed screws, replaced fan and reassembled. Move into place and secured front. Cleared faults and worked perfectly.

Threw the old one out - plugged the new one in. Steak came out just as ordered - medium rare.