CIQ71062V (1999) Campbell Hausfeld Compressor - Overview

This is an original manufacturer approved replacement air filter assembly which is specially designed for use with Campbell Hausfeld air compressors. Its purpose is to ensure the air that goes into the engine is free of dust and other harmful contaminants, over time it may get dirty and clogged eventually requiring replacement to maintain...Read more good air flow. This part consists of a durable metal housing with a pleated paper filter element.

This OEM Check Valve is an exact replacement for certain air compressors. The purpose of this part is to allow pressurized air into the tank and stop it from flowing back into the pump. It is made of metal, is gold, is not part of a kit or assembly, and is sold individually. When the check valve is defective, the compressor will funcyio...Read moren normally until the tank fills with air. At that point, the pump will try to restart, but the engine will only produce a humming noise. Similarly, if the tank is full of air, the motor will make a humming noise without engaging. This part is located on the tank to the discharge tube and will need to be replaced if broken or worn. You will need a wrench set and a socket set to complete this repair. Customers rate this repair as Easy.

This part is an OEM from Campbell Hausfeld. The drain cock-npt 3/8 is compatible with many air compressors, and is sold individually. The metal component allows the operator to drain the condensation out from the compressor tank. Located at the base of the tank, a wrench set is required for the replacement. Please be sure to refer the manual for further safety and repair instructions.

This OEM part is sourced directly from the manufacturer and is an exact replacement for various air compressors. This Assembly includes the valve plate and two cardboard composite gaskets. It is gray in color, and its primary purpose is to provide a seal between the cylinder head and crankcase. This part will need to be replaced if you h...Read moreear air leaking, the tank takes a long time to fill, if it is worn or damaged, or if you removed the cylinder head from the crankcase for other repairs as gaskets are a one-time use part. You will need a screwdriver, a socket set, a wrench set, and a torque wrench to complete this repair. Customers rate this repair as Easy.

Genuine Campbell Hausfeld replacement part, this item is sold individually. The ST033001AV Compression Nut is used to attach the copper tubing to certain components of the compressors listed below. Along with the Compression Nut you will need to use a compression sleeve ( or Ferrule) to seal the tube from leaking air. The Compression Nut will go on the tubing first then the Ferrule will slide into the nut.

Sourced directly from the manufacturer, this plug is an exact replacement part for a variety of air compressors. This part is sold individually, not as part of a kit or assembly. It is gold, made of metal, and will be found on the pressure switch. This part will leak when it has become defective and will need to be replaced if it is dam...Read moreaged or worn. When you install the part, apply Teflon tape to the threads before tightening it in place. You will need a wrench to complete this repair. Customers rate this repair as Easy.

This genuine replacement pressure switch is specially designed for Campbell Hausfeld air compressors. It is sourced directly from the original equipment manufacturer and it is sold individually. The purpose of a pressure switch is to control when the compressor should start and stop building up pressure. The default setting of this pressu...Read morere switch is 100psi on and 135psi off. Please note this high-quality item is sold individually.

This is an authentic OEM approved replacement part that is commonly utilized on Campbell Hausfeld air compressors. Its purpose is to ensure the air that goes into the unit is free of dust and other harmful contaminants. Over time the filter will get dirty and clogged restricting the air flow, inspect it periodically and replace filter as ...Read moreneeded to maintain peak performance. Please note this durable pleated paper filter is sold individually.

This is an authentic OEM part. The 1/2 compression sleeve is compatible with many air compressor machines. With the compression nut, this item helps to secure the exhaust tube to the front shroud. An adjustable wrench is necessary for the replacement. The compression sleeve is sold individually.

1/4

It is an identical replacement for a missing or a faulty cylinder head that was installed on a new unit. Please make sure to check appropriate diagrams for the correct location and use of this hardware. This authentic component is supplied directly from the original equipment manufacturer for Campbell Hausfeld air compressors. One durable...Read more metal cylinder head and the fasteners to secure it are included. A wrench set will be needed to perform this repair.