Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Large burner cap finish was damaged
3 of 4 peoplefound this instruction helpful.
Richard B from CLARKSBORO, NJ
Very Easy
Less than 15 mins
Just lifted old burner off with my fingers and replaced with the new one. What needs to be focused on here is the fact that Part Select has such a complete line of parts rather than the difficulty in the install.
Was this helpful?
Thank you for voting!
Oven Light Assembly damaged
5 of 10 peoplefound this instruction helpful.
Jose from Frederick, MD
Really Easy
15 - 30 mins
Nutdriver, Pliers
I have a double oven and coincidently I had to replace the two Oven Light Assemblies. I am really glad about your web site because once I got the number from my oven model you guys were the first ones that came up. Thanks to your prompt and reliable service my oven is back to its original state.
Jose Figueroa
Was this helpful?
Thank you for voting!
Replaced temperature sensor
3 of 4 peoplefound this instruction helpful.
George from LANSDALE, PA
Difficult
30 - 60 mins
Screw drivers, Socket set
un-screw temperature sensor, have to move racks and door, then open back cover board to disconnect the sensor.
Was this helpful?
Thank you for voting!
Wrong parts
2 of 2 peoplefound this instruction helpful.
AMON from MARYSVILLE, CA
Very Difficult
30 - 60 mins
Your diagram on your website says lower oven is incorrect everything on there is upper oven I ordered the wrong part because your diagrams are all wrong OK
Was this helpful?
Thank you for voting!
burner had hot spots where the matieral melted some cause a distorted flame that would spit sputter
2 of 2 peoplefound this instruction helpful.
Dan from WARROAD, MN
Really Easy
Less than 15 mins
Nutdriver
Remove the top grate and remove the top burner plate and then pull the burner out and remove the torx screw and adapter install onto the new burner and place back on the stove , good to go.
Was this helpful?
Thank you for voting!
Gas burner wasn’t burning properly
2 of 2 peoplefound this instruction helpful.
Karin from ARUNDEL, ME
Really Easy
Less than 15 mins
I ordered the new burner head and replaced it and now it works perfectly.
Was this helpful?
Thank you for voting!
shortage in wiring cause the housing to burn out
1 personfound this instruction helpful.
fred from PALM COAST, FL
Really Easy
Less than 15 mins
Replaced new light housing. Thanks to you guys for the prompt response
Was this helpful?
Thank you for voting!
flame was inconsistent. too much air.
1 personfound this instruction helpful.
Raymond J. from EASTPORT, NY
Really Easy
Less than 15 mins
replaced old with new.
Was this helpful?
Thank you for voting!
Food ran over the burner and damaged it.It was easy to place it back inII
1 personfound this instruction helpful.
Alan from PASADENA, TX
Really Easy
30 - 60 mins
It only required placing the new burner in the proper location.
Was this helpful?
Thank you for voting!
Replace temp sensor in gas range
1 personfound this instruction helpful.
Ron from PAINESVILLE, OH
Easy
15 - 30 mins
Nutdriver, Screw drivers
Part came as ordered. Hardest part was fitting plastic wiring harness through the hole with 2 layers of steel with insulation in between. Used electrical tape to stiffen the end about an inch or 2 back from harness. Job done, problem solved
Was this helpful?
Thank you for voting!
Temp probe was defective
1 personfound this instruction helpful.
Eric from SOUTHBURY, CT
Very Easy
Less than 15 mins
Threw the old one out - plugged the new one in. Steak came out just as ordered - medium rare.
Was this helpful?
Thank you for voting!
Water would fill washing drum when off
1 of 2 peoplefound this instruction helpful.
joseph from SECAUCUS, NJ
Very Easy
15 - 30 mins
Nutdriver, Pliers, Screw drivers
Remove and replaced water valve, seems to have fixed the problem
Was this helpful?
Thank you for voting!
Oven sensor not working
1 of 2 peoplefound this instruction helpful.
Mary from TUCSON, AZ
Really Easy
30 - 60 mins
Nutdriver
Very very simple repair!!!!! Works great!!
Was this helpful?
Thank you for voting!
Gas Oven will not light
1 of 3 peoplefound this instruction helpful.
Daniel from NASHVILLE, TN
A Bit Difficult
More than 2 hours
Nutdriver, Screw drivers
I was disappointed with this parts recommendation..neither part solved the problem, a first with partselect. The Range Oven sensor change out was easy and straight forward once the back lower panel was removed. The SPARK MODULE was time consuming..the module is located and accessible only by removing the range top. Having gas burners req
... Read moreuires unscrewing all the burners before tipping up the top and removing it, then removing the guard over the Module is next..it's a project, sure wish it worked when I was done!..turned out to be the oven glow bar....
My Orders
