If you are having trouble cleaning out your grease filter, or if it is damaged to the point of no return, maybe it is time to replace it. The grease filter is a ventilator that traps grease from the exhaust air. The dimensions of this part are roughly 6 inches wide, by 8 inches deep, and this specific model is silver. Replacing this part ...Read moreis an easy fix as it will snap in and out of place, with no tools required. This part is sold individually.
The relay switch may also be known as the door micro switch and is a part for your microwave. The function of this part is to monitor the door latch and communicate whether the door latch is open or closed to the electronic control board. Before making this repair, you will want to make sure to unplug your microwave and discharge the capa...Read morecitor. Your microwave capacitor is able to store electricity in large quantities even after it has been unplugged. The most common reason for replacing your relay switch is if the microwave will not turn on but your timer still runs..
This 20-watt lightbulb is most commonly found in the microwave. The lightbulb brightens the interior of the microwave while it is running so you can keep an eye on the food while it cooks. You will need to unplug the microwave while performing this repair. Microwaves continue to have an electrical charge directly after being unplugged, so...Read more please use caution. To access the light bulb, you will need to remove the outer cover surrounding the bulb on the top of the inside of the microwave. This is an OEM part that comes right from the manufacturer.
The tray, used in a microwave, holds food plates and containers on it. The tray, also known as a turntable, rotates when the microwave is heating up food to ensure the plate of food is evenly heated. If your glass tray is broken, shattered, or is not rotating when heating, it is best to replace it for better heating results. The tray has ...Read moredimensions of 33 x 35.6 x 2.5 cm and weighs 455 grams. Refer to the manual provided by the manufacturer for installation instructions and guidance.
The roller guide sits underneath the glass turntable tray in your microwave. If your microwave turntable tray is not rotating properly, you may need to replace the turntable roller guide. The function of this part is to house the glass plate, and rotate to cook food evenly. This part has a round piece in the middle, approximately 2 inches...Read more in diameter, and 3 arms which are approximately 4 inches in length each. Each arm has a small plastic wheel on the end that supports the glass turntable tray. This part is an OEM part sourced directly from the manufacturer, and is sold individually.
This turntable motor is used in microwaves. This is what rotates the glass tray so that your food is heatied evenly. The specs for this synchronous motor are 120 Volts, 60Hz, 3rpm, and 2.1 Watts. It features two 3/16-inch male spade terminals, which is what attaches to the internal wiring of your appliance. The motor also includes mountin...Read moreg holes; there are two mount holes on either side of the part. This replacement motor is approximately two inches in diameter, and it is sold individually. Before you attempt this repair make sure you unplug your microwave.
This is an exhaust damper assembly for a microwave, which is also known as a microwave vent damper. The damper directs air flow through the vent duct from the top or rear of your microwave, depending on your model, to allow the air to flow outside and prevent outside air from coming in. You will need to uninstall your microwave from the w...Read moreall to access the exhaust damper. Once you have gained access to the damper, simply slide the old part out, and slide the replacement part in. This is an OEM replacement part that is sourced directly from the genuine manufacturer.
The microwave door latch spring creates tension, and engages the door latch when the door is closed. This spring is made completely of metal, and is approximately 1 inch long. If your microwave door will not open or close properly, the microwave will not start. You may need to remove the control panel to gain better access to where the sp...Read morering attaches, so make sure the power is disconnected from the microwave. This part is sold individually.
NOTE: Remember to discharge the capacitor for your microwave before beginning this repair. The capacitor can hold a potentially lethal charge even when the power has been disconnected from the microwave itself.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Timer would run but the microwave won't start
91 of 149 peoplefound this instruction helpful.
Tim from Chicago, IL
Easy
30 - 60 mins
Screw drivers
I first removed the top plate above the microwave door (3 screws), then I removed the plate containing the buttons and clock. The microwave has 3 relay switches and they are in a little holder. The holder was too difficult to remove so I just removed the bottom switch and replaced. The microwave started right up.
Was this helpful?
Thank you for voting!
Broken Handle
44 of 64 peoplefound this instruction helpful.
Brent from Bend, OR
Easy
Less than 15 mins
Screw drivers
Removed the retaining clip that keeps the door on, took the door off. Removed the plastic rim that is clipped into place. Removed old screws holding on handle and replaced.
Was this helpful?
Thank you for voting!
Wave guide cover was cracked. Oven started to spark and make popping noises when in use.
39 of 57 peoplefound this instruction helpful.
amy from corona, CA
Really Easy
Less than 15 mins
Part arrived in one day. Old part snapped right out and new snapped right in. One minute repair with no more sparking and no need to invest in a new microwave... which is what I thought I was going to have to do.