All Installation Instructions for Crosley Refrigerator CFD28WIQSC

Thin, flexible edge on outermost door gasket was tearing from the main gasket, likely due to being rubbed when accessing refrigerator..

Gasket is held in place by an extrusion on the back side. Simply remove the old gasket and press the new gasket's extrusion into the track on the door.

Parts Used:

GASKET-DR,MAGNETIC FF GREY 36

Dennis from Oley, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Water outlet tubing leaking in elbow behind water filter

Most difficult and time-consuming part of the job was clearing the refrigerator of food and shelving. Replaced tubing as it had split in the factory bend of the tubing directly behind the water filter. Take your time and don't get in a hurry.

Parts Used:

Water Inlet Tube

Chuck from GRIFTON, NC
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

New off brand water filter could not be removed from the water filter base

Removed the water lines from the old base. Installed new base and reconnected water lines. Installed new filter.Turned on the water line behind the refrigerator. Opened Refrigerator door to watch for leaks. No Leakes. The new filter base was

Parts Used:

MANIFOLD FILTER

James from ELK GROVE, CA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Previous seal had a tear and cold air was leaking around seal

Pulled the old seal out of the groove. Placed new seal in the groove. New seal has to be heated and massaged to get it into proper form so it does not leak. I have been continuously heating and massaging to get the seal to get it in the proper form. Been working on it for a week. Almost there.

Parts Used:

GASKET,FREEZER DRAWER,GREY

Daniel from Hampton, NH
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

There is no power, due to the COVID-19 pandemic there no Tech support available,

My repair plan is to continue buying parts for it until is starts working. I notices a large rusty stain on the back of the refrigerator, so I replaced the Ice Maker. Then, I replaced the Evaporator Motor. Yet nothing will come on.
I called Conn's Home Plus where I bought the Frigidaire Refigerator back in February 2014. The Tech said that It needs a Board-main Power (computer part). So I it ordered from PartSelect. It is due here by July 20, 2020. The Parts and Tech cost is now over Five Hundred ($500) dollars.
HELP!! I need INSTRUCTIONS, HELP!!!
Albert F. Alfaro in San Antonio, TX.

Parts Used:

Ice Maker Assembly

Albert from SAN ANTONIO, TX
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Screw drivers, Socket set

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Refrigerator wasn't staying cool enough

Easily removed the old gasket and put the new ones on exactly the same way the old ones came off but in reverse

Parts Used:

GASKET-DR,MAGNETIC FF GREY 36

Karl from Brookfield, CT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Replaced door gaskets with new ones

Removed the old door gaskets by hand and attached the new ones by inserting the edges in the existing grooves

Parts Used:

GASKET-DR,MAGNETIC FF GREY 36

Andres from Golden Valley, MN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

GASKET WORN AND LEAKING

SIMPLY REMOVE THE OLD GASKET PULLING LIGHTLY BY HAND
THEN PUSHING THE NEW GASKET BY HAND

Parts Used:

GASKET-DR,MAGNETIC FF GREY 36

Dennis from Lancaster, SC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

ice maker is stuck on crushed ice.

We had someone to come and look at it and we were told it was the solenoid valve. The repairman unstuck it for us and said when it does it again, he would have to order the part. We took it upon ourselves to order the part and DIY. We replaced the part that we were told was the problem and "guess what" it's still not fixed. It's still shooting out crushed ice. Will have to call repair guy back out here to see what we did wrong.

Parts Used:

Refrigerator Ice Dispenser Solenoid

Mary from MAGNOLIA, AR
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Screw drivers

3 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

One blade broke from condenser fan

The part i recieved, from parts select was a larger in circumfrence (<1/4) than the original. However i was not aware of this until after i treid to repair it.

I removed the broken fan from the condenser. This was very sipmle.

When i pluged the refridgerator back in to the outlet the fan tried to start up but soon began to make aloud noise, due to there not being enough clerance.

Parts Used: