CF1540 (Type 0) Porter Cable Compressor - Overview

Frequently referred to as a Drain Plug, this Drain Valve is used to drain any condensation that has collected inside the tank to prevent the tank from rusting. It is not part of a kit or assembly, is sold individually, made of brass, is gold, and will be found at the bottom of the air tank. This part will need to be replaced when it is ...Read moreno longer able to provide a proper seal, or if it is visibly worn or damaged. You will need a wrench to complete this repair. Customers rate this repair as Easy.

This fan is an exact replacement part for use in air compressors and is sourced directly from the manufacturer. It is made of durable black plastic and is used to cool the compressor during operation. It is not part of a kit or assembly and is sold individually. This part is located on the end of the motor shaft and will be visibly brok...Read moreen or worn when it needs to be replaced. You will need a screwdriver, a socket set, and a drill to complete this repair. Customers rate this repair as Easy.

Sourced directly from the manufacturer, this part is an exact replacement for various air compressors. Its primary purpose is to control the airflow through the pump. This part is an assembly that includes the plate gasket and seals. When this part is malfunctioning, the tank will take longer to fill or will not be able to fill at all. I...Read moret will need to be replaced once it becomes damaged or worn. You will need a wrench set and a socket set to complete this repair. Customers rated this repair as Easy.

This is a genuine Craftsman part for use with Craftsman Air Compressors. The compression ring creates an airtight seal between the cylinder and piston and helps facilitate heat transfer between the piston and cylinder wall. The compression ring on a piston head is a wear and tear item. It is, often, a cause of an air compressor failing to...Read more produce air. This part is sold individually. Unplug the air compressor and bleed air from the tank before installing this part. Wear work gloves to protect your hands.

O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. rnrnThere are many causes for O-Ring failure. The most common among power tools are: • Extrusion and Nibbling - The O-ring has ragged, tattered edges. ...Read moreThese are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • Abrasion - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that it too rough, contains grit or is too smooth to allow lubrication. • Over Compression - The O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • Heat Hardening - The O-ring has a pitted or cracked surface, and is often flattened on both sides. Caused by temperature exceeding o-ring capacity. • Weather/Ozone Cracking - The O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching (greater that 5%) causes similar cracking.

O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-Ring failure. The most common among power tools are: • Extrusion and Nibbling • The O-ring has ragged, tattered edges. Thes...Read moree are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • Abrasion • One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that it too rough, contains grit or is too smooth to allow lubrication. • Over Compression • The O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • Heat Hardening • The O-ring has a pitted or cracked surface, and is often flattened on both sides. Caused by temperature exceeding o-ring capacity. • Weather/Ozone Cracking • The O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching (greater that 5%) causes similar cracking.

This part is sold individually and helps to support the compressor. The rubber bumper recess attaches to the tank. A screwdriver may be helpful when replacing this part. It may become broken and will need to be replaced. This is an OEM part directly sourced from the manufacturer for use in compressors made by Porter Cable, DeVilbiss, Black & Decker, DeWALT, and Bostitch.

This is an authentic OEM part for use with Craftsman Compressors. The check valve lets pressurized air flow into the tank and prevents air from flowing back into the pump. A failed check valve will apply high air pressure to the head of the pump preventing the motor from restarting once the tank has filled. The most common reason for repl...Read moreacing the check valve is if the motor starts with an empty tank but won't start when the tank is full. This part is sold individually. The tool that you will need to replace the check valve is an adjustable wrench and Teflon tape.

It is a genuine manufacturer-sourced replacement screw which is specially designed for use with air compressors. This is a standard hardware which has multiple applications depending on the model of your unit, make sure to check appropriate diagrams for the correct location and use of this item. It is a high-quality hex head screw which i...Read mores made of durable metal and it is sold individually, over time the threads may wear out eventually requiring a replacement.

This is a genuine replacement part manufactured for use with air compressors from DeWalt. This part creates an airtight seal between the elbow and the tube. You may need a wrench to replace this part. This assembly but sleeve is sold individually and made of metal.

This saddle mount cup is an OEM direct from Craftsman for air compressors. This part holds the screw in place. You will need a wrench to remove the bolts that go through it. It is recommended that you wear gloves when replacing this part. This saddle mount cup is made of steel and sold individually.