CF15 Bostitch Nailer - Overview

Diagrams for CF15

See every part. Know exactly what you need.

Page A

Parts for the CF15

$50.77

KIT-TRIGGER VALVE

★★★★★

(1)

Part #TVA6

This is a genuine Bostitch replacement part that fits all BT brad nailers and all S32 staplers. If trigger leaks air or if tool misfires often, try replacing trigger valve. This kit contains one (1) each of: valve assembly (including both O-rings), lubricant, spring pin punch, and repair instructions. Please note that two (2) O-rings are ...Read more

Read less

$9.11

Piston Head Valve

Part #174054

Restore reliable firing power with this piston head valve, a key component that controls airflow within the nailer's cylinder assembly. By directing air pressure to drive and return the piston during each firing cycle, it helps maintain consistent performance and efficient operation. A worn, cracked, or damaged valve can cause air leaks, ...Read more

Read less

$6.40

O-RING-44.7MMX3.5MM

Part #174055

Help keep your pneumatic nailer operating at peak performance with this O-ring seal, designed to create an airtight seal between internal components and maintain the air pressure needed for consistent driving power. A worn or damaged O-ring can lead to air leaks, reduced performance, and weak or inconsistent firing, making replacement an ...Read more

Read less

$11.87

GASKET-FRAME/DEFLECT

Part #174050

This item is an authentic OEM sourced part that is intended to be used with pneumatic nailers from Bostitch. The gasket is used to seal the connection between the deflector assembly and the frame of the nailer. A hex driver may be needed to install this item, please note the gasket is priced as a single item.

$6.40

O-RING-45.5MMX2.0MM

Part #174058

It is a genuine OEM supplied replacement part and is specially designed for Bostitch nailers. The purpose of this o-ring is to provide an air-tight seal for the cylinder, over time it may wear out and begin to crack eventually requiring a replacement. Make sure to refer to the appropriate diagrams of your model for the correct location an...Read more

Read less

$6.40

O-RING-36.0MMX4.0MM

Part #174060

This is an authentic Bostitch part compatible with nailers. An O-ring is a flexible circle that creates a pressure seal between rigid parts. Multiple sizes of O-ring are used with these tools; see manual for correct size needed and its placement. • Size: 36 mm x 4 mm

$32.87

KIT, CONTACT TRIP CONVERSION

Part #CNTK1

This authentic OEM sourced component is made for use with Bostitch nailers and staplers. It is a special contact trip conversion kit that can be installed on the tool to fire upon contact with a surface. Please make sure to refer to the owners manual and the appropriate diagrams of your model for the correct location and application of th...Read more

Read less

$6.40

SPRING HOLDER

Part #P2845203062

Hex.Soc.Hd.Bolt

Part #S2710620101

$6.40

SPRING

Part #P2325202662

Bumper

Part #P2900000400

$4.08

Deflector Cover

Part #P2900002266

Repair Tips From Fixers Like You

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

would not fire nails

10 of 15 people found this instruction helpful.

Richard from Bogalusa, LA
A Bit Difficult
30 - 60 mins
Pliers, Screw drivers

remove 2 Philips head screws, drive out drift pins with drill bit. Remove TVA6 replace with new TVA6 making sure TVA6 is completely seated and slots are aligned with drift pin holes! Drive in drift pins. Replace trigger and screws.
This did not solve the problem as suggested by Parts select.
Replaced Head Valve Seal...Problem re ... Read more

Read less

Was this helpful?