CED126SDW1 Crosley Dryer - Overview

Diagrams for CED126SDW1

See every part. Know exactly what you need.

Parts for the CED126SDW1

$15.00

Multi Rib Belt - 92-1/4"

★★★★★

(433)

Part #341241

This dryer drum belt (Whirlpool Dryer Belt, Drive Belt) has four ridges, three grooves and is 1/4" wide, and 92 1/4 inches in length. It comes in black and is made of rubber. The belt transfers the rotation of the motor to turn the drum. The belt attaches to the drum, idler pulley, and motor pulley.

$58.42

Heating Element - 240V 5400W

★★★★★

(306)

Part #279838

The heating element (Flat Can Heating Element 5400W, Heating Element, Whirlpool Dryer Heating Element, Dryer Heating Element) provides heat to the dryer. It is metal and measures 10.5 inches long, 7.5 inches wide, 2 inches deep. The element attaches to the heater housing. This part can break as a result of wear and tear. This can be mater...Read more

Read less

$26.82

Dryer Cycling Thermostat

★★★★★

(102)

Part #WP3387134

This thermostat (Dryer Operating Thermostat, Dryer Cycling Thermostat, Cycling Thermostat, Dryer Thermostat) is used to maintain a temperature of 155 degrees in the dryer drum. The internal bias heater also allows this thermostat to provide a low heat temperature of approximately 140 degrees when the low temperature setting is selected. T...Read more

Read less

$47.40

Thermal Cut-Off Kit

★★★★★

(152)

Part #279816

The thermal cut-off (Dryer Thermal Cut-Off Fuse Kit, Dryer Thermal Cut-Off Kit) prevents the dryer from overheating when the dryer high limit thermostat fails in a closed circuit condition. This part fails when the heater housing does not have adequate airflow through it; this is normally caused by restriction in the exhaust vent, plugged...Read more

Read less

$35.80

Maintenance Kit

★★★★★

(362)

Part #4392065

The drum support roller kit (Dryer Repair Kit) allows the dryer to tumble properly by supporting the drum cylinder. The idler pulley provides the tension required for a multi-ribbed belt. The belt attaches to the drum, idler pulley, and motor pulley. If your dryer is damaged, it may be making loud, squeaking, and/or squealing noises while...Read more

Read less

$18.22

Rear Drum Support Roller Kit

★★★★★

(150)

Part #349241T

The drum support roller kit allows the dryer to tumble properly by supporting the drum cylinder. The kit includes two drum rollers, four tri-rings, and one palnut (or retaining washer). The kit does not include a belt or idler pulley and rollers are not sold individually. The drum support roller kit may need to be replaced if the dryer is...Read more

Read less

$20.37

Dryer High Limit Thermostat

★★★★★

(32)

Part #WP3977767

A dryer high-limit thermostat (High Limit Thermostat, Hi-Limit Thermostat, Dryer High-Limit Thermostat) is a switch that is actuated by temperature change. This high limit thermostat acts as a safety mechanism to keep the dryer from overheating. If your thermostat is malfunctioning, your dryer may not heat. This thermostat is located bene...Read more

Read less

$45.29

Dryer Door Handle - White

★★★★★

(339)

Part #W10861225

This white OEM dryer door handle is used to open and close the dryer's door. Comprised of plastic and 6-by-2-inches in dimension, the handle is sold individually and attaches to the dryer door. Your dryer door may need replacing if you've accidentally pulled too hard on the door handle in opening. This will be more likely to happen over t...Read more

Read less

$57.38

LINT SCREEN ASSY, WOD

★★★★★

(211)

Part #W11778253

This manufacturer-certified dryer lint filter is used to collect lint during the dryer cycle, to prevent damage to the machine and to prevent lint from sticking to clothes. This model comes in white and is easy to install. It slides into the lint filter slot in your dryer. If there is visible damage to the screen then it's time to replace...Read more

Read less

$11.77

Roller Support Tri-Ring

★★★★★

(5)

Part #WPW10512946

If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pulley shaft, or on the rear drum roller shaft. In either case, you will need to remove the front panel of the dryer and the drum to access the...Read more

Read less

$6.40

Leveling Foot

★★★★★

(13)

Part #49621

If your washer shakes or vibrates loudly when it reaches its max speed, check that the leveling legs are even. To ensure that the washer is firmly on the ground using all four legs, adjust the legs so that the machine is level, and tighten the locking nuts on the legs that are threaded. Keep the washer as close to the floor as possible. Y...Read more

Read less

$97.46

Drive Motor with Pulley

★★★★★

(36)

Part #279827

This OEM drive motor is designed to operate the drum in electric and gas dryers by turning the drive belt, enabling proper rotation during drying cycles. Compatible with most Whirlpool-incorporated dryer brands manufactured before 1996, it includes a pre-attached pulley, which is not available separately. If the motor has shorted out or f...Read more

Read less

Questions And Answers for CED126SDW1

Ask our experts a question about this model and we'll get back to you as soon as possible!

Sort by:

Brian - For model number CED126SDW1

December 23, 2019

Drum keeps moving off the rear drum supports. Replaced drum supports last year and have had no trouble until last week when the belt broke. Have had it running correct for.A few minutes then stops.

Hello Brian and thank you for writing. It certainly sounds like you might have faulty drum support roller shafts you should check for signs of damage, and replace it if needed. We hope this helps. Please contact us anytime. right side # PS11753705 left side # PS11753706 We hope this helps. Please contact us anytime.

$53.20

Dryer Drum Support Roller Shaft Right Side

Was this helpful?

Margie - For model number CED126SDW1

June 9, 2023

Dryer works but the timer does not. It never cuts off. Help

Hi Margie, thank you for asking. You may need to check the timer, part number PS11731364, to fix the issue. It controls the electrical components and the duration of the dryer cycles. We hope this sorts out your problem!

$148.25

Timer - 60 Hz.

Was this helpful?

James - For model number CED126SDW1

April 9, 2024

Timer switch for drying unit

Hello James, thank you for reaching out. The timer you are looking for is part number PS11731364. If you require assistance to place an order, please contact customer service!

$148.25

Timer - 60 Hz.

Was this helpful?

Common Symptoms of the CED126SDW1

How this model fails, and the parts that fix it.

Noisy

Fixed by
these parts

Show All

Not Heating

Fixed by
these parts

Marks left on clothes

Fixed by
these parts

Heat stays on after drum has stopped

Running With Door Open

Fixed by
these parts

Show All

Touchpad does not respond

Videos related to models starting with CED126SDW1

Watch our pros, then fix it yourself.

Replacing the Heating Element - 240V 5400W

Replacing the Maintenance Kit

Replacing the Multi Rib Belt - 92-1/4"

Replacing the Dryer Cycling Thermostat

Replacing the Rear Drum Support Roller Kit

Replacing the Thermal Cut-Off Kit

Replacing the Dryer High Limit Thermostat

Replacing the CATCH

Repair Tips From Fixers Like You

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Dryer motor runs, but no heat

2308 of 2510 people found this instruction helpful.

Gadi from Irvine, CA
Really Easy
30 - 60 mins
Nutdriver

To reach the heating element you only need to open the back cover of the dryer (about 8 nut-head screws). Remember to disconnect the power.

To remove the heating element there are two small nut-head screws. Remove the two electric wires. Then you can pull the heating element away.

You can check the heating element wi ... Read more

Read less

Was this helpful?

No Heat

903 of 969 people found this instruction helpful.

Vernon from Niceville, FL
Really Easy
15 - 30 mins
Nutdriver

First tried heating element and thermal fuse with no luck. Ordered thermal cutoff and fixed problem. Had I used an ohm meter first I would have determined problem before having ordered heating element and fuse, as both had resistance. I wast just lazy and ordered the took the most common failed components first before taking dryer back ... Read more

Read less

Was this helpful?

Dryer would run with no heat.

731 of 766 people found this instruction helpful.

Remie from Mahopac, NY
Really Easy
15 - 30 mins
Nutdriver

The repair was easy. the most time consuming part was vacuuming the dust from the back of the Dryer, The repair required removing screw from the back panel of the dryer. Then removing screws from the heating element and unplugging the wires. The only moderately diffculy part was swapping the sensor form the old element.

Was this helpful?