CDWT980R30SS General Electric Dishwasher - Parts

If you are having trouble rolling your dish rack in and out, there could be an issue with the rollers or axles. Check the existing rollers and axles for any visible physical damage. Replace the parts if the rollers or their axles are damaged. These rollers attach to the dish rack allowing the rack to roll in and out with ease. This pack i...Read morencludes 8 gray rollers measuring at approximately 1.75 inches L x 0.75 inches W x 1.75 inches H. Each roller comes with an axle.

This is a basket for washing flatware or silverware in your dishwasher.

This complete lower rack assembly is a genuine replacement part designed for select GE dishwashers, including models sold under Hotpoint, Haier, Monogram, and Café brands. Engineered to securely hold plates, bowls, pots, and pans during the wash cycle, it ensures optimal water coverage and prevents breakage. Constructed from high-quality ...Read morematerials, the rack offers long-lasting durability and resistance to heat and detergent wear. Newer versions may feature an enhanced wheel assembly with protective coverings that keep the wheels aligned and prevent detachment, allowing for smoother sliding in and out of the dishwasher. Common signs that replacement is needed include difficulty moving the rack, rust or discoloration, broken tines, and poor cleaning performance due to misaligned dishware.

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoid on the valve open and close according to the desired amount of water needed.

This end cap is sold individually. It is the same end cap used on the right and left side, for both front and back. It attaches to the end of the upper rack slide rail, and prevents the rack from falling when being pulled out too far.

This detergent dispenser assembly is attached to the inner door panel of a dishwasher. This part holds detergent and dishwasher rinse products in a covered container. If your dispenser will not open, close, dispense detergent properly, or the dishes are coming out of the dishwasher dirty, replacing this part can solve these problems. The ...Read moretools needed for this installation project are a #2 Phillips screwdriver and needle-nose pliers. To repair, first remove screws from the bottom of the inner door panel. Next, remove connecters, wires, and screws from the dispenser to access it and replace with new dispenser. Refer to the manual provided by the manufacturer for further installation instructions and guidance. Unplug dishwasher from power source as a safety precaution.

Comes with the axles.

This gasket lines the inside cabinet in the dishwasher.

The hinge link on your dishwasher connects the spring to the dishwasher door hinge. If the hinge link becomes cracked or damaged, you may not be able to shut or lock your dishwasher door properly. In this case, you will need to replace the hinge link. Pull out your dishwasher to inspect the hinge and spring, if the link is broken, it may ...Read morebe disconnected and on the ground already. If not, you can remove the hinge arm link by simply disconnecting it from the hinge and spring, then replacing it with the new part. The hinge arm link is a small piece of white plastic about an inch and a half long. It is sold individually, and is an OEM part from the manufacturer.

This genuine rinse-aid dispenser cap is an original replacement part from GE, designed for use with GE dishwashers. It covers the rinse agent port and securely seals the dispenser to keep the rinse aid contained until it's needed during the wash cycle. The cap is commonly replaced if it becomes lost or damaged. No tools are required for i...Read morenstallation, making it a quick and easy fix. This part is sold individually and is built to meet OEM standards for compatibility and performance.

This dishwasher retainer connects to the removable tine.

This OEM-compatible screw is designed for use with many GE dishwashers. Measuring 8-16 HXW and 1/2" in length, this stainless steel screw secures the middle spray arm hub to the upper rack assembly, ensuring stable and effective spray arm performance. Sold individually, this durable metal fastener requires a nutdriver for proper installation.