This grey OEM dishwasher tub gasket is a 73" grey rubber part that creates a seal around the dishwasher to prevent any water leakage during a cycle. If it's damaged or broken, you'll start seeing water leaking out. If broken, it should be replaced. Refer to your model number and user manual to ensure this part is right for you. When makin...Read moreg this repair, open the dishwasher door and take out the lower dish tray for better access. Pull out the old gasket, and clean the channel with a rag. Push the new gasket into place into the notch on the door, which you should see upon close inspection, using a flat-head screwdriver for assistance if necessary. We do not recommend cutting any additional length off on the tub gasket if any is present during your repair.
The heating element nut is used to connect the heating element to the dishwasher tub. If water is leaking from underneath your dishwasher, you may need to tighten or replace the heating element nut. Replacing the nut is an easy job, does not require any specialty tools, and should not take you more than 10 minutes. For our step by step gu...Read moreide, click the video below. The brass nut measures 7 inches in length x 1 inch in width x 5 inches in height, and fits most dishwashers. To see if this part is compatible with your dishwasher, check the list of compatible brands below.
If your dishwasher is leaking or not draining properly, you may need to replace the drain hose. The drain hose connects to the pump located below the lower spray arm and aids in proper dishwasher drainage. This white and black plastic hose is 7.5 feet long. For this repair, you will need either a 1/4-inch or 5/16-inch nut driver, dependin...Read moreg on your model. You will need to remove the lower access panel on your dishwasher to complete this repair; it is often easier to remove the dishwasher from the cabinet to do so. Be sure to disconnect the dishwasher from both the power and water supply before completing this repair.
This door spring is manufactured for a dishwasher door. The door spring applies tension to the dishwasher door so that the door does not drop too quickly when it is opening. If the door drops too quickly, it could cause damage to the dishwasher door or dishwasher door hinges. This spring is sold individually. Check the spring on the oppos...Read moreite side of the dishwasher door, they often wear at the same rate so you may want to replace both springs for exact tension on either side. No tools are required for this repair. This is an OEM replacement part.
This dishwasher heating element is a genuine replacement component designed to maintain optimal water temperature during the wash cycle and assist in drying dishes at the end of the cycle. Positioned at the bottom of the dishwasher tub, it ensures efficient cleaning and drying performance. Compatible with a wide range of models from Frigi...Read moredaire, Kenmore, Crosley, Electrolux, and other related brands, this element replaces older versions and restores proper function when symptoms such as poor cleaning, inadequate drying, or water leaks occur. Installation requires disconnecting power to the appliance to ensure safety. Sold individually.
This filter is for dishwashers.
The filter removes food particles and debris from the water to prevent the drain from clogging.
Follow the instructions in the manual when installing this part.
This is a basket for your dishwasher. It sits in the lower dishrack and holds small utensils during a washing cycle. This basket has six smaller sections where you can separate your cutlery into specific groups. This silverware holder is made entirely of plastic with a crisscross pattern allowing water and small food particles to pass thr...Read moreough it during the cleaning process. This model is grey and roughly 14 inches long, about 6 inches high, and almost 4 inches thick.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
dishwasher was leaking water
177 of 213 peoplefound this instruction helpful.
Charles from Milton, FL
Really Easy
Less than 15 mins
Screw drivers
I removed old tub gasket, which the door presses against to make a seal, and put the new one in. Flat tip screwdriver was used to gently press gasket in.
Was this helpful?
Thank you for voting!
Water leaking under the dishwasher
78 of 89 peoplefound this instruction helpful.
Dennis from Tryon, NC
Really Easy
Less than 15 mins
Wrench (Adjustable)
I looked under and found that 2 brass nuts that secured the heater element through the base housing of the dishwasher has split down each side of the nut and no longer was tight enough to keep water from leaking around either end of the heater element. I powered down the dishwasher at the circuit breaker and then reached under the dishwa
... Read moresher and pulled away the 2 wires that were attached to each side of the heater element. I removed the two nuts and replaced them with the parts I ordered from partselect.com. I then put the appropriate wires back at the end of the heater element and ran the dishwasher to check for leaks. No leaks... it was fixed.
Read less
Was this helpful?
Thank you for voting!
Dishwasher door practically fell open
54 of 60 peoplefound this instruction helpful.
Daniel from Fremont, NE
Really Easy
Less than 15 mins
All I had to do was replace the spring and retainer on the side of the dishwasher which amounted to pulling it out far enough to reach the eyelet that the hook went into and then stretching it to the retainer attached on the other end. I really like partselect, I have done some things in the past and they are very helpful on the site and
... Read more on the phone and I would recommend them to anyone and I would not normally do that unless it has been an excellent experience.