Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Food ran over the burner and damaged it.It was easy to place it back inII
1 personfound this instruction helpful.
Alan from PASADENA, TX
Really Easy
30 - 60 mins
It only required placing the new burner in the proper location.
Was this helpful?
Thank you for voting!
some of electrodes not working at times,found were bad,wires had some insulation missing, clips looked burnt,found all new parts replaced
1 personfound this instruction helpful.
Dana from LEEDS, AL
Really Easy
More than 2 hours
Pliers
the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.
Was this helpful?
Thank you for voting!
shortage in wiring cause the housing to burn out
1 personfound this instruction helpful.
fred from PALM COAST, FL
Really Easy
Less than 15 mins
Replaced new light housing. Thanks to you guys for the prompt response
Was this helpful?
Thank you for voting!
flame was inconsistent. too much air.
1 personfound this instruction helpful.
Raymond J. from EASTPORT, NY
Really Easy
Less than 15 mins
replaced old with new.
Was this helpful?
Thank you for voting!
Temp probe was defective
1 personfound this instruction helpful.
Eric from SOUTHBURY, CT
Very Easy
Less than 15 mins
Threw the old one out - plugged the new one in. Steak came out just as ordered - medium rare.
Was this helpful?
Thank you for voting!
Replace temp sensor in gas range
1 personfound this instruction helpful.
Ron from PAINESVILLE, OH
Easy
15 - 30 mins
Nutdriver, Screw drivers
Part came as ordered. Hardest part was fitting plastic wiring harness through the hole with 2 layers of steel with insulation in between. Used electrical tape to stiffen the end about an inch or 2 back from harness. Job done, problem solved
Was this helpful?
Thank you for voting!
stripped control knob
1 of 2 peoplefound this instruction helpful.
michael from milford, CT
Really Easy
Less than 15 mins
remove and replace the same .
Was this helpful?
Thank you for voting!
Oven sensor not working
1 of 2 peoplefound this instruction helpful.
Mary from TUCSON, AZ
Really Easy
30 - 60 mins
Nutdriver
Very very simple repair!!!!! Works great!!
Was this helpful?
Thank you for voting!
Water would fill washing drum when off
1 of 2 peoplefound this instruction helpful.
joseph from SECAUCUS, NJ
Very Easy
15 - 30 mins
Nutdriver, Pliers, Screw drivers
Remove and replaced water valve, seems to have fixed the problem
Was this helpful?
Thank you for voting!
Part does not look like the part that needs to be replaced
1 of 3 peoplefound this instruction helpful.
P from FULLERTON, CA
Really Easy
30 - 60 mins
I have no clue what wire goes where because there is no thing to refer to or instructions of any kind . I have not been able to install the part.
Was this helpful?
Thank you for voting!
Gas Oven will not light
1 of 3 peoplefound this instruction helpful.
Daniel from NASHVILLE, TN
A Bit Difficult
More than 2 hours
Nutdriver, Screw drivers
I was disappointed with this parts recommendation..neither part solved the problem, a first with partselect. The Range Oven sensor change out was easy and straight forward once the back lower panel was removed. The SPARK MODULE was time consuming..the module is located and accessible only by removing the range top. Having gas burners req
... Read moreuires unscrewing all the burners before tipping up the top and removing it, then removing the guard over the Module is next..it's a project, sure wish it worked when I was done!..turned out to be the oven glow bar....
Start by removing all screws 3 for each burner total of 15 t-15 bit is required then proceed to remove spark igniters 5 total slight pull next step would be to slide a screwdriver under top left and right side to remove top shelf. There you will have access to the parts you need to replace. When done just reverse installation instruction
... Read mores to complete
Read less
Was this helpful?
Thank you for voting!
Broken Probe Sensor
0 of 1 peoplefound this instruction helpful.
Michael from Tucson, AZ
Really Easy
Less than 15 mins
Replaced it
Was this helpful?
Thank you for voting!
Deflector oven/gas flame deflector replaced due to hole melted from glowbar igniter
0 of 1 peoplefound this instruction helpful.
Barry from Coventry, RI
Easy
Less than 15 mins
Nutdriver, Screw drivers
Removed oven convection fan cover for more room to remove/replace lower oven bottom. Deflector is attached underneath oven bottom and you will need new self tapping sheet metal screws to replace old ones. My deflector actually had hole melted in it from glowbar igniter directly underneath it. Glowbar remains white hot until selected oven
... Read moretemp is reached...poorly designed.
My Orders
