CCGS985SET4SS General Electric Range - Instructions

Bake ignitor would not glow. Removed racks and lower pan to access the ignitor. Removed two attaching screws and unplugged electrical connector. Installed new ignitor. Hint: Gas will not flow unless both the bake and broil ignitors are operational. Ignitors are interchangable; you can test ignitors by swapping them.

replaced the ignitor and it has worked perfectly the last week - Service repair walked away from the service call stating it was too random - you website state 91% cause, you were correct I wish I had done this 2 years ago

(I could hold a torch on the igniter to start it, then it would work, but would not initially heat up on its own). Pull up and remove oven door. Remove racks. Remove 2 thumb screws in back of bottom plate and remove plate. Remove 1 screw on cover plate. remove 2 screws on igniter and unplug. Splice wires from new igniter to old plug with ceramic wirenuts (included). (Manufacturer changed plug design). re-install everything. (Sears wanted $80.00 for the part, Appliance Factory wanted $47.00).

It was quite easy. Uplug the ingnitor and remove two screws from bracket holding it in place along side gas pipe. Plug in new ignitor and and reinstall two screws thru bracket to secure ignitor against gas pipe. Thats it!! Oh, you must remove floor of oven (two Screws,back wall)and remove broiler and door/tray by pulling all the way out to access the ignitor and gas pipe assembly.

The job was made very simple primarily due to the repair video that was available on your site when I ordered the part that I was looking for. The job can be done in less than 15 min, but it took me a little bit longer because of some rusted screws that didn’t want to come out so easily. I also decided to take of the front door (not mentioned in the video) just to make it a bit easier to reach the igniter component. The door comes off very easy by opening the door about 6 inches and pulling up and off of the door hinges. Again for a novice like me the video was a life saver.

removed oven door & broiler draw took out bottom panel in oven removed part from burner tube reinstalled everything piece of cake works great now

new igniter had a plastic wire coupling that did not fit with the soves wires; cut off coupling and connected wires with ceramic wire nuts given, remounted ignitor and fired up the oven.

the part fit perfect so 5 min, done, thanks for the right part the frist time, I will be back

Unhooked old one, installed new one. Piece of cake.

I was at my in-laws and they expressed how they needed to buy a new stove, since it stopped working. They explained the problem to me and I immediately checked the broiled (it worked fine). Knowing that stoves have 2 electric igniters, i knew 1 was bad.
The site got me the part in 3 days (regular shipping).
The repair was pretty easy.
- Removed 2 screws that hold the floor of the oven.
- Removed 2 nuts that held the igniter to the oven.
- Removed the bottom drawer of the oven, and unplugged the igniter.
- Finally, I screwed in the new igniter, fed the wire down to the plug and plugged it in.
- Then I tested the oven before putting it back together, IT WORKED!)
The only negative was, when I was removing the racks and pans from the oven, one of them happened to be filled with oil for frying, and it got all over me. Be prepared for anything when working on someone else's appliance.

Just replaced the igniter and it works fine now

Replaced it

Removed oven convection fan cover for more room to remove/replace lower oven bottom. Deflector is attached underneath oven bottom and you will need new self tapping sheet metal screws to replace old ones. My deflector actually had hole melted in it from glowbar igniter directly underneath it. Glowbar remains white hot until selected oven temp is reached...poorly designed.

It was so easy ! take out 2 screws , unplug old igniter, plug in new igniter, replace screws and turn on the heat!! Thanksgiving Dinner is back to my house with the whole Family!!!

Repair was very simple. It was a five minute job including time taken to remove old part with a screwdriver and then it was a matter of plugging in the new part ant attaching it to the oven.