Models > CA10SMC

CA10SMC General Electric Freezer - Overview

Sections of the CA10SMC

[Viewing 3 of 3]
Keep searches simple, eg. "belt" or "pump".
Shoulder Screw – Part Number: WR01X10623
Shoulder Screw
★★★★★
★★★★★
(2)
PartSelect #: PS1483099
Manufacturer #: WR01X10623
This is a self-tapping sheet metal screw and is used in conjunction with multiple appliances in your household. This part is size eight and has 18 threads to the inch. The AB in the name indicates tha...
$14.72
  In Stock
Water Tubing Clip – Part Number: WR1X5278
Water Tubing Clip
PartSelect #: PS295031
Manufacturer #: WR1X5278
$6.68
  In Stock
Screw – Part Number: WR1X1249D
Screw
PartSelect #: PS294429
Manufacturer #: WR1X1249D
Comes 12 in a pack.   No Longer Available
Power Cord – Part Number: WR23X10300
Power Cord
★★★★★
★★★★★
(2)
PartSelect #: PS759476
Manufacturer #: WR23X10300
This heavy-duty cord has a three-pronged plug (2 electrical, 1 grounding). The power cord supplies power to your refrigerator, allowing it to keep the contents inside cool. There could be an issue wit...
$24.13
  In Stock
BEARING-HINGE BOTTOM – Part Number: WR02X12310
BEARING-HINGE BOTTOM
★★★★★
★★★★★
(2)
PartSelect #: PS1483212
Manufacturer #: WR02X12310
$12.90
  In Stock
Run Capacitor - 220Vac – Part Number: WR62X10058
Run Capacitor - 220Vac
PartSelect #: PS1766253
Manufacturer #: WR62X10058
This is a run capacitor. It is 220 VAC (volts alternating current) and is used in conjunction with your freezer. This part helps the compressor kick on and off while maintaining a constant temperature...   No Longer Available
Drain Plug – Part Number: WR02X10073
Drain Plug
PartSelect #: PS284532
Manufacturer #: WR02X10073
$24.39
  Special Order
R134 DRIER – Part Number: WR86X25269
R134 DRIER
PartSelect #: PS12727537
Manufacturer #: WR86X25269
The filter dryer filters refrigerant that travels through the sealed system of the refrigerator.
$56.83
  In Stock
SUPPORT – Part Number: WR2X7621
SUPPORT
PartSelect #: PS298561
Manufacturer #: WR2X7621
  No Longer Available
SUPPORT – Part Number: WR2X7622
SUPPORT
PartSelect #: PS298562
Manufacturer #: WR2X7622
  No Longer Available
SHELF SUPT – Part Number: WR2X6250
SHELF SUPT
PartSelect #: PS298196
Manufacturer #: WR2X6250
  No Longer Available
LEVELNG JACK – Part Number: WR2X5676
LEVELNG JACK
PartSelect #: PS298100
Manufacturer #: WR2X5676
$8.61
  In Stock

Questions And Answers for CA10SMC

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Symptoms of the CA10SMC

[Viewing 3 of 3]
Leaking
Fixed by
these parts
Show All
Frost buildup
Fixed by
these parts
Show All
Will Not Start
Fixed by
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The freezer door was catching when opened and frost was building inside telling me that the seal wasn't good.
I called the local GE dealer for repair. The repair person arrived and told me that he could not get the part. The freezer was too old. Then he charged me $60 for coming out. I went online and did a search for parts with the model number above. I found Partselect.com and the diagrams showed which part I needed. It was in stock and I ordered it. My husband and I removed the door to the freezer, pushed the part into the hole at the bottom of the door and put the door back on its hinges. It works perfectly. Thank you.
Parts Used:
BEARING-HINGE BOTTOM
  • Paulette from Great Falls, MT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
10 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Two of the two leveling jacks of this old refrigerator were missing and had to be replaced.
I ordered four leveling jacks from this site for the refrigerator using a slightly different model number (my model was not listed). I assumed that the jacks all had the same shaft diameter and thread size. However, it turned out that the two front jacks had half-inch shaft diameters. It could be that originally there were rollers in front. The two rear jacks had quarter-inch shafts with "feet" for supporting them on the floor. So, I had to return the four jacks I had ordered and find another solution. I found two half-inch threaded bolts at the local hardware store that fit the front holes perfectly. I purchased 3.5 inch bolts to give me enough room to find the proper adjustment. I used wooden blocks and a crow bar to raise one side of the refrigerator high enough to screw in the leveling jacks. I used an adjustable crescent wrench to turn the bolts' hex heads until they were the proper height. I used the two original quarter-inch jacks in the rear holes and adjusted them to the proper height to level the refrigerator on the concrete floor where it is located. Then I removed the wooden blocks and tested to make sure the refrigerator did not wobble. I found that using the two bolts (no leveling jacks for the front holes could be found) for the front jacks proved to be the ideal solution. The job took me about thirty minutes, including the time it took to move the refrigerator into its final location and adjust the leveling jacks once more to create a solid stance so that the refrigerator did not wobble. While I had the refrigerator away from the wall, I removed the rear panel and cleaned the blades of the cooler fan and removed dust and dirt build up near the compressor with a vacuum cleaner. Then, I screwed the panel back into position, moved the refrigerator into its final place in a corner of the garage and made sure there was enough air space around it to allow for proper air circulation. This took me about twenty more minutes. I plugged it back in and listened to it come alive again. It is old but has never needed a repair and keeps everything cooled or frozen. I would suggest using threaded hex-head bolts in place of original leveling jacks if they cannot be obtained. Problem solved.
Parts Used:
LEVELNG JACK
  • Bruce K from RESTON, VA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    30 - 60 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!