C950-52435-0 Snow Blower - Overview

This is a round, inline fuel filter with 0.25-inch nipples, used in a variety of lawn and garden equipment. It is sourced from the original equipment manufacturer and has the capability to filter out particles as small as 150 microns in size. The filter is designed to remove any dirt or debris in the fuel to avoid contaminating the engine...Read more. Over time, it is common for the filter to become clogged with dirt/debris or damaged, resulting in less fuel entering the engine, engine misfiring, stalling, and overall lower performance from your equipment. To replace the faulty fuel filter, first disconnect the fuel lines with pliers or a clamp tool and then pull out the old filter. Install the new filter into the housing and reattach the fuel lines to complete your repair.

This ball bearing is sourced from the original equipment manufacturer and can be used in a variety of outdoor equipment. It has an inner diameter of 11/16 inches. The ball bearing provides support for the rotating parts in your equipment and reduces the amount of friction they are subject to during use. If the bearing is not adequately lu...Read morebricated or has worn down, you may hear grinding or squeaking from your equipment and notice excessive vibration when in use. It is important to address this issue promptly as a faulty ball bearing can potentially damage the parts located near it. To replace the ball bearing, use a pry bar or bearing puller to pry it out of its housing. Clean the housing thoroughly and press your new ball bearing in position. Note that when pressing the ball bearing into place, apply force only to the outer portion of the bearing.

This is a genuine manufacturer sourced replacement cap for the fuel tank. It is specially designed for use with Briggs and Stratton engines installed on lawn and garden equipment. It is used to keep the fuel in the fuel tank and protect it from outside contaminants. It features a retainer that will remain in the tank to keep the cap from falling out or getting lost. This plastic cap is sold individually.

This hex locknut has a special locking feature to prevent it from loosening due to vibrations or movement. It has a 1/4 inch diameter and a 20 threads-per-inch pitch. You will find it securing various parts of your lawn equipment, such as blade assemblies, engine mounts, or handles. A broken locknut cannot fasten components together tight...Read morely. Replace any damaged locknuts to keep your machine securely assembled and functioning properly. Loosen a locknut from your machine by turning it with a wrench or a socket. This durable metal locknut is an OEM hardware. It is sold individually, so read your user manual to determine how many you will need. Consider getting extras if you are replacing one, as these locknuts tend to wear out together.

This is an authentic Murray replacement part that has been sourced from the original manufacturer to be used with riding lawnmowers. The metal washer is used to provide spacing between the steering spindle and the front axle assembly. This item is sold individually, please note two washers may be needed.

This ignition key is an authentic replacement part. It is sourced directly from original equipment manufacturer for use with Murray riding lawn mowers/tractors. This is a safety feature for unauthorized use of the mower. The key is inserted into the switch and it allows you to start the unit. Includes two (2) metal ignition keys.

This is a genuine manufacturer-approved item that is specially designed for Craftsman snowblowers. It is an identical replacement for a missing or damaged knob that was originally installed on a new unit. The purpose of this component is to provide a user with a comfortable grip to secure the adjusting chute. Please make sure to refer to ...Read morethe appropriate diagrams of your model for the exact location and the correct installation of this component. Keep in mind this durable plastic knob is sold individually.

This authentic replacement part is designed for use with Murray, Simplicity and Snapper snowblowers. Flange bearings are used to provide support for a shaft while reducing friction between rotating parts. The rollers take the load and spin, distributing the weight evenly while the minimal contact area of the roller reduces friction. Beari...Read morengs experience constant wear from pressure, heat, vibration, and friction. Because of this, many bearings need to be periodically replaced. Make sure to check the diagrams of your model for the exact location and the correct installation of this component. It is sold individually. You will need a screwdriver and a wrench set to take apart the housing in order to gain access to this flange bearing. Keep in mind the screws utilized to secure this component are sold separately.

This hex center lock nut is sourced from the original manufacturer for use in lawn and garden power equipment. It is a hexagon-shaped fastener for bolts/studs that is responsible for the keeping the bolt/studs secure during use. The nut is made of metal and has a diameter of 5/16 of an inch and a thread pitch of 18 internal threads per in...Read morech. Over time the threads in the nut can wear down and the nut itself may crack or break. It is important to replace it as soon as necessary to avoid damaging your equipment. Use a socket or wrench to remove the old nut and thread the new one on. Make sure to order the correct number of nuts for your equipment as each nut is sold individually.

This OEM universal joint pin is used within various models of snowblowers to hold the rod and yoke together inside the deflector/chute assembly. If you notice excessive vibrations, clunking, or limited range of motion within the chute mechanism, it is worth inspecting to check for a broken pin or other internal damage. To prevent any futu...Read morere issues with your universal joint pin, make sure to keep it adequately clean and lubricated and inspected regularly. This pin is made of a high-quality metal, measures 1-inch long and .375-inches thick, and is sold as an individual part.

This is a genuine Murray, Snapper, and Simplicity part sourced directly from the manufacturer for use in snowthrowers. The clutch spring boot is made out of rubber. A set of pliers may be necessary during the installation of this item. It may become broken and will need to be replaced. This is available as an individual replacement part.

This is a Briggs & Stratton, Murray, Snapper, and Simplicity replacement part directly sourced from the manufacturer for use in engines and snowblowers. The choke shaft knob is made out of plastic. It might require a screwdriver and a socket set to replace this item. It will need to be replaced if it breaks. This part is sold individually.