BVM210FA (2012-10) Poulan Leaf Blower / Vacuum - Overview

This Genuine OEM fuel filter is designed to maintain the performance and longevity of your equipment by preventing dirt and debris from entering the carburetor. Located inside the fuel tank, this essential component ensures clean fuel delivery, protecting the engine from potential damage caused by contaminants. Sold individually, the filt...Read moreer is built to meet original equipment standards for fit and function. Over time, the filter may become clogged, restricting fuel flow and making engine starts more difficult. For optimal performance, it should be replaced—not cleaned—at the first sign of blockage or wear.

This is the Genuine Craftsman replacement part. It is made out of Flexible Rubber and is Sold Individually. The purpose of the 530069216 Tank Purge Line is to return the excess fuel that is in the carburetor after the primer bulb has been pushed. The excess fuel is forced through the purge line back into the fuel tank. Over time the Tank Purge Line will become brittle and crack and will need to be replaced.

This OEM Piston Ring is used to provide a seal between the piston and cylinder wall. It attaches around the piston, inside the groove. It will require a screwdriver, allen wrench, torx wrench and socket set and is rated as "Hard" to install. The part is silver, metal, and individually sold. If broken due to general wear/fatigue you will h...Read moreave poor compression within the cylinder, causing a loss of power. If broken, damaged or worn, the part should be replaced. Refer to your make, model, and diagram to ensure this is the correct part.

This genuine OEM foam air filter is designed to protect the carburetor and engine of your blower by preventing debris from entering. It is housed within an air filter cover. If the filter shows signs of tears, holes, or excessive dirt buildup, it is considered broken. Not replacing a damaged or clogged foam air filter can lead to various ...Read moreconsequences. The engine may suffer from reduced performance, decreased fuel efficiency, and increased wear and tear over time. To replace the filter, access the air box filter cover on your machine and remove the old filter. Refer to your user guide for specific installation instructions. It may be recommended to apply two-cycle oil to the packaging and allow the filter to absorb it. Afterward, remove the filter from the packaging and gently squeeze out any excess oil using a paper towel. This replacement part is sold individually.

This OEM Vacuum Bag holds grass and leaf clippings when the blower is switched to vacuum mode, and is attached to the exit port. It is constructed of white fabric. If broken due to wear/fatigue it will no longer be able to hold clippings and should be replaced. Refer to your make, model and diagrams to see if this is the right part for your machine.

This flywheel is an authentic manufacturer replacement part for use with lawn and outdoor equipment. The flywheel is a heavy, circular disc that has magnets that create an electric charge sent to the spark plug to create the spark that ignites the fuel and air mixture in the engine. It is attached to the engine crankshaft by a key known a...Read mores a shear pin or flywheel key. This assembly is a critical component in the starting and running of your power equipment. Over time, the magnets on the flywheel will wear down, and the flywheel may chip and crack. A faulty flywheel will result in a loss of power, excessive shaking during use, and difficulty starting the equipment. Remove the flywheel using a flywheel puller. Position the new flywheel on the crankshaft and secure it with the retaining nut and flywheel key. This flywheel is sold as an individual replacement part.

Tubes on leaf blowers are not only used to project air, but also suction it and guide any debris from your yard into your blower collection bag. This upper tube is designed for and compatible with various models of leaf blower vacuum and is made of plastic. Measuring approximately 18-inches in length, this tube connects to a lower tube an...Read mored is used as the connecting tube to the leaf blower itself. Over time and through use, leaf blower tubes can crack and break or simply not connect, and if your tube is broken it needs to be replaced. To replace this tube, simply twist the tube clockwise to remove it, and twist the new tube on counterclockwise until a click is felt.

This O-ring gasket kit is an authentic manufacturer replacement kit used in leaf blowers. It includes the muffler shield, carburetor gasket, cylinder base gasket, and crankshaft oil seal/O-ring. The muffler shield protects the engine muffler and prevents accidental burning or damage to the surrounding components. The carburetor gasket sea...Read morels the area between the carburetor and intake manifold to prevent fuel and air leakages. The cylinder base gasket seals the area between the engine cylinder and the engine block to prevent combustion gases from escaping. The crankshaft O-ring prevents oil leakages. These gaskets can fail at the same time, due to wear, aging, or damage, leading to leakages, loss of pressure, and decreased equipment performance. If you notice difficulties in starting and running the leaf blower, you will likely need to replace these gaskets. This kit is designed to allow you to replace these gaskets all at once for optimal engine performance and savings. To complete the repair, you will need needle nose pliers, a T-27 Torx bit, a Phillips head screwdriver, and a flat-head screwdriver.

This restrictor nozzle is a genuine OEM part found at the end of the lower blower tube/nozzle. It narrows the tube opening to create a concentrated stream of air that moves faster, and with more precision. Over time the restrictor nozzle may become damaged, blocked, or fall out of alignment with the tube. Once the nozzle is no longer func...Read moretioning, it will be unable to control the airflow or provide high power output. Replacing the restrictor nozzle is a simple repair which does not require any tools or fasteners. Simply twist and pull the nozzle from the tube. Align the new nozzle with the opening on the tube and twist it into place. Ensure that it is firmly locked in position before attempting to use the blower again.

This is a standard hardware which has multiple applications based on your tool. It is sourced from original equipment manufacturer for use with a variety of power equipment. Please refer to diagrams for proper application. This screw is made out of metal and it is sold individually. Requires a hex key or an allen wrench to install or remove it.

This is a genuine Craftsman replacement part that has been sourced from the original manufacturer to be used with blowers. The plastic tube is the lower portion of the assembly that guides air that is produced by the blower's impeller. This item may not require tools to install and is sold individually.

This genuine replacement screw is a high-quality OEM part designed for use with Paramount and Poulan gas-powered lawn and garden equipment. It is specifically engineered to secure the starter rope within the pulley, ensuring reliable starting performance. Made from durable metal, this specialty screw is sold individually. Installation...Read more Tip: A flat-head screwdriver is required for removal and installation. For proper placement and application, please refer to your equipment’s model diagram.