BN200A Porter Cable Nailer - Overview

O-rings are designed to contain thousands of pounds of pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-Ring failure, such as pressure, friction, temperature or chemicals. The most common are: • Extrusion and Nibbling ...Read more• O-ring has ragged, tattered edges. These are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • Abrasion • One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that is too rough, contains grit or is too smooth to allow lubrication. • Over Compression • O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • Heat Hardening • O-ring has a pitted or cracked surface, and often is flattened on both sides. Caused by temperature exceeding o-ring capacity. • Weather/Ozone Cracking • O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching causes similar cracking.

Genuine Manufacturer Sourced replacement part designed for use with Porter Cable Nailers/Staplers. This item is made out of Metal has a slit and it is Sold Individually. This part is installed on top of the piston/connecting rod. Its purpose is to create a seal in the cylinder so that it can build pressure. If this part wears your tool will not be able to operate as intended.

This is an authentic OEM sourced component which is specially designed for Porter Cable staplers and nailers. It is an identical replacement for a missing or faulty rolled pin that was originally installed on a new unit, please make sure to check the appropriate diagrams of your model for the correct location and application of this hardw...Read moreare. Keep in mind this high-quality item is made of durable metal and is sold individually.

This is a genuine manufacturer sourced replacement part that is specially produced for use with Porter Cable nailers and staplers. The purpose of this piston bumper is to keep the piston from hitting the bottom of the cylinder and damaging it. Because this part gets so much abuse it has a tendency to crack and fall apart. This item is made of durable rubber material and it is sold individually.

This is an authentic replacement part manufactured for use with Porter Cable brad nailers and staplers. The special housing cap is the end cap that fits on the rear of the body and the cap includes the exhaust deflector. The special housing cap is available as an individual replacement part, please note the mounting hardware is available separately.

This is an authentic high quality item that is specially produced for Porter Cable nailers and staplers. This is one of the seals for the trigger valve assembly which is sold separately. Please note this durable rubber seal is sold individually.

O-rings are designed to contain thousands of pounds of pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. Of the many causes for O-Ring failure, the most common are: • Extrusion and Nibbling - O-ring has ragged, tattered edges. These are commonly...Read more caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • Abrasion - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that is too rough, contains grit or is too smooth to allow lubrication. • Over Compression - O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • Heat Hardening - O-ring has a pitted or cracked surface, and often is flattened on both sides. Caused by temperature exceeding o-ring capacity. • Weather/Ozone Cracking - O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching causes similar cracking.

This is an authentic OEM part for Porter Cable nailers. The trigger pivot pin attaches to the housing and is made of metal. A set of pliers might be needed during the installation process. This part may become bent or broken and will need to be replaced. This part is available as an individual replacement.

It is a genuine item that is supplied directly from the original equipment manufacturer for use with Porter Cable nailers and staplers. The purpose of this item is to ensure a tight seal between connected parts, please make sure to check the appropriate diagrams of your model for the correct location and application of this hardware. Keep...Read more in mind this high-quality item is made of durable rubber and is sold individually.

O-rings are designed to contain thousands of pounds of pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-Ring failure, such as pressure, friction, temperature or chemicals. The most common are: • Extrusion and Nibbling ...Read more• O-ring has ragged, tattered edges. These are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • Abrasion • One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that is too rough, contains grit or is too smooth to allow lubrication. • Over Compression • O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • Heat Hardening • O-ring has a pitted or cracked surface, and often is flattened on both sides. Caused by temperature exceeding o-ring capacity. • Weather/Ozone Cracking • O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching causes similar cracking.