BM80544 (090079457) Homelite Pressure Washer - Overview

This detergent suction kit, also known as a soap or chemical injection kit, is designed for use with a pressure washer. This is a genuine OEM part designed to inject soap into the water stream of your pressure washer, and includes the main injector valve, two differently sized O-rings, a spring, and a ball bearing. One end of this kit wil...Read morel be threaded into the washer, and the other will lead to your cleaner with a siphon, which is sold separately. This injection kit would need to be replaced if the nozzle is leaking, the injector fails to work properly, or water is getting into the soap dispenser. To replace, simply unscrew the previous injector and remove it, then fit the small O-ring inside the threaded end of the new injector, along with the ball bearing and then spring. Wrap the larger O-ring around the base of the threaded end, and apply a layer of lubricant, before installing the new injector and securing it.

This is an original part from Ryobi. The wheel is constructed of high-quality plastic, and is compatible with several pressure washers. This component is fitted on the main frame assembly, allowing the operator to easily move the cleaning device when needed. A flat head screwdriver and a mallet may be helpful for the removal and replacement. The wheel is sold individually.

This OEM outlet tube, also known as a hose connector, allows pressurized water to flow from the pump of your pressure washer to the nozzle. Connecting the hose to the handle assembly and the spray wand, it is where the water exits from your machine so you can direct the stream towards a desired surface. You can tell if an outlet tube is b...Read moreroken when it has visible cracks or holes and when water leaks or sprays from the connection points or along the tube. A damaged or blocked tube can result in a loss of pressure and potentially premature wear or machine failure. To remove the outlet tube, use a wrench set to unscrew it from the pump. Please note that this replacement part is sold separately from the pump assembly.

(25 ft., 3000 psi) This water hose is for pressure washers. Water hose carries water from the pump to the spray wand. Wear work gloves to protect your hands when installing this part.

This replacement soap tank is an authentic high quality item that is supplied from original equipment manufacturer for use with Homelite pressure washers. It is the main container that holds the soap, please note the blue tank cap is sold separately. This soap tank with outlets is made from durable plastic and it is sold individually. Rep...Read morelacing it is a simple task that should only require a wrench to remove the two bolts that secure it to the frame.

The collar attaches to the spindle. This item is made out of plastic and metal and is sold individually. This is an authentic part from Ryobi and Homelite for use in pressure washers. An allen wrench might be necessary during the installation of this part. It will require replacing if it becomes broken.

This authentic manufacturer-sourced part is specially designed for use with portable generators. It is an identical replacement for a missing or a faulty component that was installed on a new unit. The part helps to secure fuel tank to the main frame, please make sure to refer to the appropriate diagrams of your model for the correct loca...Read moretion and application of this hardware. Keep in mind this high-quality isolator is made of durable rubber and is sold individually.

It is a genuine OEM item that is made for use with Homelite and Ryobi and Homelite pressure washers. This is a special component which helps to provide a tight fit between connected components. Over time it may wear out or get damaged eventually requiring a replacement. Make sure to check the appropriate diagrams for your model to ensure ...Read morethe proper repair procedure. It is made of durable metal and is sold individually. A wrench might be needed to replace this inlet filter connector.

This is an original part from Homelite. The lock nut (m8 x 1-1/4 mm) is compatible with many pressure washers, and is sold individually. The metal lock nut helps to secure various components of the pressure washer. A wrench, hex key and screwdriver are often needed for the installation.

This is an authentic OEM part designed to be used on the Ryobi pressure washers listed below. This very low pressure nozzle is designed to draw soap/chemical mixture from the detergent tank, and spray it onto surfaces for cleaning. It is usually called a soap nozzle but can also known as a chemical injector tip. Includes one (1) nozzle.