BC800 (UT-15183) Homelite Trimmer - Overview

This OEM spring, also known as a recoil or rewind spring, is housed in a container and is used to retract the starter rope on various lawn equipment models. Over time and through use, the spring will eventually lose its tension, and will break. If your starter rope has no resistance when pulling it, the starter spring is likely broken. Me...Read moreasuring at approx. 3-inches by 3-inches, this spring is suitable for use with a variety of lawn equipment models and is sold individually.

Springs are used within outdoor power equipment to provide tension and shock absorption, depending on their application and use. This spring is designed for use within trimmers/brush cutters and is made to provide tension on the spool reel mechanism, and in some cases may be used to advance the line whenever portions of it are cut off. Th...Read moreis spring measures approximately 1.3-inches in length when extended and comes as an individual part. If you notice the line/spool in your trimmer is not advancing or is coming too quickly, the spring may be damaged and need replacing. Since this spring is a high-use part, it is not uncommon for it to lose tension over time and need to be replaced. To replace the spring, you will need to unscrew the covering cap, remove the spool feeding reel, remove the old spring and install the new spring with the rest of the assembly. Make sure to feed the line back into the appropriate feeding holes prior to operation of the trimmer.

This is a genuine OEM replacement part, it is sold individually. The purpose of the 900994004 Carburetor Gasket is to prevent an air leak, which would cause the engine to run poorly. It is advised to replace these gaskets when replacing or repairing the carburetor.

Genuine OEM replacement part, this item is sold individually. This Clutch Drum is used on all of the outdoor products shown below. It contains the screw to attach this part to the spindle of the engine. It is usually a Torx T-25 Screw or a T-20. Once the engine gets to a certain RPM the clutch will expand and come in contact with the inside of the clutch drum. This will start the rotation of the Trimmer drive shafts.

This is a genuine OEM replacement part, it is sold individually. The Housing and Eyelet contain the spring and the spool and string for the models listed below. The cutting string is inserted through the eyelets, then the spool is inserted into the housing, it is then attached by the spool retainer.

This is a genuine OEM sourced replacement starter rope, not an aftermarket equivalent. This part is used to pull start Homelite and Ryobi handheld lawn and garden equipment. This rope is made from durable fabric and it is sold individually. Please note, the grip handle is sold separately. Replacing this starter rope you will need a screwdriver.

Genuine OEM replacement part, This item is sold as a kit. This is the complete Stringhead Assembly for the Trimmers shown below. It is a dual line head. To install this part, slide it on the spindle or shaft of the Trimmer The kit contains two Spool Retainers to secure the Stringhead. The red one has left hand threads and the black one ha...Read mores right hand threads. It will depend on the model you have, on which Spool Retainer to use. The cutting line diameter used in this Stringhead is .080

Throttle Cable with a 11" Conduit. For a 15" conduit see Related Item.

This is a genuine manufacturer approved replacement part. This specially designed heat dam is used on a variety of gas powered trimmers/brushcutters and edgers. This part plays an important role because it works as a spacer for carburetor allowing it to stay cool. This part is made out of plastic and it is sold individually. You will need a wrench to remove the carburetor when replacing this item.

This is a genuine OEM replacement strap made for various yard tools. This fabric strap features one metal lobster clasp, which attaches to the tool via the strap hanger. It is adjustable with a plastic slide adjuster. One strap is included.

It is an authentic component that is supplied by the original equipment manufacturer for use with Homelite and Ryobi handheld string trimmers. This is an identical replacement for a missing or a faulty handle bar clamp that was installed on a new unit. The part is utilized to secure the handle bar. Please make sure to refer to the appropr...Read moreiate diagrams of your model for the correct location and application of this component. Keep in mind this high-quality clamp is made of durable metal and is sold individually.