BC2500AZ (UT-15205) Homelite Trimmer - Overview

This OEM spring, also known as a recoil or rewind spring, is housed in a container and is used to retract the starter rope on various lawn equipment models. Over time and through use, the spring will eventually lose its tension, and will break. If your starter rope has no resistance when pulling it, the starter spring is likely broken. Me...Read moreasuring at approx. 3-inches by 3-inches, this spring is suitable for use with a variety of lawn equipment models and is sold individually.

This is a genuine OEM replacement part, sold individually. This Bumper helps keep the fuel tank in place, and minimizes vibration of the fuel tank. This part is used with a variety of string trimmers, compatible with the models listed below.

This flanged star washer is a manufacturer-sourced replacement part designed for use trimmers. It is also known as a tooth lock washer due to its serrated inner edge which resembles inward facing teeth. These teeth bite into the head of the fastener and provide a better grip than standard washers. This washer also has a flange on one side...Read more which is a lip that extends past the edge of the washer. It helps to distribute the load of the fastener over a wider area to provide extra stability and a more secure hold. Over time the washer may wear down or become damaged. To remove the washer, first unthread the bolt/screw it is fastened on. Use pliers to grip the washer and gently twist it off. Place the new washer over the fastener with the teeth facing toward the surface being fastened and insert it into the designated hole. Ensure that it is locked into place. Each washer is sold individually.

Springs are used within outdoor power equipment to provide tension and shock absorption, depending on their application and use. This spring is designed for use within trimmers/brush cutters and is made to provide tension on the spool reel mechanism, and in some cases may be used to advance the line whenever portions of it are cut off. Th...Read moreis spring measures approximately 1.3-inches in length when extended and comes as an individual part. If you notice the line/spool in your trimmer is not advancing or is coming too quickly, the spring may be damaged and need replacing. Since this spring is a high-use part, it is not uncommon for it to lose tension over time and need to be replaced. To replace the spring, you will need to unscrew the covering cap, remove the spool feeding reel, remove the old spring and install the new spring with the rest of the assembly. Make sure to feed the line back into the appropriate feeding holes prior to operation of the trimmer.

This is a genuine OEM replacement part, it is sold individually. The purpose of the 900994004 Carburetor Gasket is to prevent an air leak, which would cause the engine to run poorly. It is advised to replace these gaskets when replacing or repairing the carburetor.

Genuine OEM replacement part, this item is sold individually. This Clutch Drum is used on all of the outdoor products shown below. It contains the screw to attach this part to the spindle of the engine. It is usually a Torx T-25 Screw or a T-20. Once the engine gets to a certain RPM the clutch will expand and come in contact with the inside of the clutch drum. This will start the rotation of the Trimmer drive shafts.

Genuine OEM replacement part, this item is sold individually. This Fuel Cap is is on the fuel tank on the outdoor products shown below. This is a vented Fuel Cap. It includes a gasket inside the Cap.

This item has been OEM sourced and is intended to be used with gas-powered trimmers and pruners from Ryobi & Homelite. The gasket is used to seal the connection between the cylinder and the crankcase. It is recommended to replace gaskets when servicing the motor to ensure proper seals and spacing when the parts are reassembled. This item is priced as a single part.

This is a genuine OEM replacement part, it is sold individually. The Housing and Eyelet contain the spring and the spool and string for the models listed below. The cutting string is inserted through the eyelets, then the spool is inserted into the housing, it is then attached by the spool retainer.

This is a genuine OEM replacement part, it is sold individually. This is the fuel pick-up line it is connected to the line coming from the fuel tank by means of a inline fuel fitting. It is then connected to the carburetor. It is used on the model numbers shown below.

It is an authentic manufacturer-approved replacement trimmer head assembly that is specially designed for use with Homelite and Ryobi string trimmers. This trimmer head is designed to quickly and efficiently cut through the grass. It is a complete assembly which includes the bump head knob, spool with string, cover and metal eyelets. Please note this high-quality string head assembly is sold individually.

This is a genuine OEM replacement part, it is sold individually. The purpose of this part is to connect the fuel line extending from the fuel tank to the fuel line that connects to the carburetor. Over time the fuel lines will become brittle and oversized. They will have to be replaced. This would be a good time to replace the Fuel Fitting also.