BC2500AZ (UT-15202) Homelite Trimmer - Overview

This spool retainer is sourced from the equipment manufacturer for use in trimmers. It is a plastic knob, measuring 2 inches in diameter, with a threaded metal bolt in the center. The retainer has a right hand thread, and it is used to secure the spool within the trimmer head to prevent it from coming loose during operation. The retainer ...Read moreengages with the trimmer head to lock the spool in place, while it also advances the cutting line for greater cutting efficiency. If the threads on the retainer bolt wear out or the plastic body becomes damaged, the retainer will be unable to engage with the trimmer head, causing the line to tangle, the spool to come loose, and lowering the cutting performance of the trimmer. Remove the trimmer head cover and detach the retainer from the assembly. Position the new spool retainer in the assembly and thread it firmly into place.

This grass deflector acts like a shield so that grass clippings are directed away from you and the surrounding areas while you are operating your trimmer. It is often located near the bottom of your trimmer, close to the cutting head. This assembly also includes the line cutting blade, which maintains the proper length of the trimmer line...Read more. If the assembly is cracked, bent, or missing, grass clippings may fly in unintended directions. This can be dangerous if your trimmer throws debris towards you or others nearby, so it is important to replace the damaged deflector. To replace the assembly, you will need a screwdriver to remove the flat washer, wing nut and, the hex screw from the grass deflector. Please be aware that this OEM grass deflector is sold individually.

This OEM spring, also known as a recoil or rewind spring, is housed in a container and is used to retract the starter rope on various lawn equipment models. Over time and through use, the spring will eventually lose its tension, and will break. If your starter rope has no resistance when pulling it, the starter spring is likely broken. Me...Read moreasuring at approx. 3-inches by 3-inches, this spring is suitable for use with a variety of lawn equipment models and is sold individually.

This is a genuine OEM replacement part, sold individually. This Bumper helps keep the fuel tank in place, and minimizes vibration of the fuel tank. This part is used with a variety of string trimmers, compatible with the models listed below.

This is a genuine OEM replacement part, it is sold individually. The purpose of the 900994004 Carburetor Gasket is to prevent an air leak, which would cause the engine to run poorly. It is advised to replace these gaskets when replacing or repairing the carburetor.

Genuine OEM replacement part, this item is sold individually. This Clutch Drum is used on all of the outdoor products shown below. It contains the screw to attach this part to the spindle of the engine. It is usually a Torx T-25 Screw or a T-20. Once the engine gets to a certain RPM the clutch will expand and come in contact with the inside of the clutch drum. This will start the rotation of the Trimmer drive shafts.

Genuine OEM replacement part, this item is sold individually. This Fuel Cap is is on the fuel tank on the outdoor products shown below. This is a vented Fuel Cap. It includes a gasket inside the Cap.

This item has been OEM sourced and is intended to be used with gas-powered trimmers and pruners from Ryobi & Homelite. The gasket is used to seal the connection between the cylinder and the crankcase. It is recommended to replace gaskets when servicing the motor to ensure proper seals and spacing when the parts are reassembled. This item is priced as a single part.

This is a genuine OEM replacement part, it is sold individually. The Housing and Eyelet contain the spring and the spool and string for the models listed below. The cutting string is inserted through the eyelets, then the spool is inserted into the housing, it is then attached by the spool retainer.

It is an authentic manufacturer-approved replacement trimmer head assembly that is specially designed for use with Homelite and Ryobi string trimmers. This trimmer head is designed to quickly and efficiently cut through the grass. It is a complete assembly which includes the bump head knob, spool with string, cover and metal eyelets. Please note this high-quality string head assembly is sold individually.

This is a genuine OEM replacement part, it is sold individually. The purpose of this part is to connect the fuel line extending from the fuel tank to the fuel line that connects to the carburetor. Over time the fuel lines will become brittle and oversized. They will have to be replaced. This would be a good time to replace the Fuel Fitting also.