BC1725SBR (UT-15158-R) Homelite Trimmer - Overview

The Fuel Tank is an OEM replacement part. It is compatible with the models shown below. It includes the fuel lines, fuel cap and fuel filter. If you need to order the fuel tank bumpers, they are sold individually as part number 98792.

This OEM spring, also known as a recoil or rewind spring, is housed in a container and is used to retract the starter rope on various lawn equipment models. Over time and through use, the spring will eventually lose its tension, and will break. If your starter rope has no resistance when pulling it, the starter spring is likely broken. Me...Read moreasuring at approx. 3-inches by 3-inches, this spring is suitable for use with a variety of lawn equipment models and is sold individually.

This is a genuine OEM replacement part, sold individually. This Bumper helps keep the fuel tank in place, and minimizes vibration of the fuel tank. This part is used with a variety of string trimmers, compatible with the models listed below.

This flanged star washer is a manufacturer-sourced replacement part designed for use trimmers. It is also known as a tooth lock washer due to its serrated inner edge which resembles inward facing teeth. These teeth bite into the head of the fastener and provide a better grip than standard washers. This washer also has a flange on one side...Read more which is a lip that extends past the edge of the washer. It helps to distribute the load of the fastener over a wider area to provide extra stability and a more secure hold. Over time the washer may wear down or become damaged. To remove the washer, first unthread the bolt/screw it is fastened on. Use pliers to grip the washer and gently twist it off. Place the new washer over the fastener with the teeth facing toward the surface being fastened and insert it into the designated hole. Ensure that it is locked into place. Each washer is sold individually.

This is a genuine OEM replacement part, it is sold individually. The purpose of the 900994004 Carburetor Gasket is to prevent an air leak, which would cause the engine to run poorly. It is advised to replace these gaskets when replacing or repairing the carburetor.

Genuine OEM replacement part, this item is sold individually. This Fuel Cap is is on the fuel tank on the outdoor products shown below. This is a vented Fuel Cap. It includes a gasket inside the Cap.

This item has been OEM sourced and is intended to be used with gas-powered trimmers and pruners from Ryobi & Homelite. The gasket is used to seal the connection between the cylinder and the crankcase. It is recommended to replace gaskets when servicing the motor to ensure proper seals and spacing when the parts are reassembled. This item is priced as a single part.

This is a genuine OEM replacement part, it is sold individually. This is the fuel pick-up line it is connected to the line coming from the fuel tank by means of a inline fuel fitting. It is then connected to the carburetor. It is used on the model numbers shown below.

Genuine Ryobi replacement part, this assembly is sold individually. This is the part of the trimmers shown below that contains the cutting line,string head housing,spring and spool with the cutting line already installed in the spool. It is secured to the trimmer by using the 308042003 Spool Retainer (Red-LH Thread) which is threaded into the shaft. This is a dual line cutting head.

The cupped washer attaches to the tri-arc blade with the use of the lock nut. This part is an OEM from Ryobi and Homelite to be used in brushcutters and trimmers. It is made of metal and helps to keep the cutting tool in place. A wrench will be needed if this part needs to be replaced. This washer is priced as an individual replacement part.

This is a genuine manufacturer approved replacement part. This specially designed heat dam is used on a variety of gas powered trimmers/brushcutters and edgers. This part plays an important role because it works as a spacer for carburetor allowing it to stay cool. This part is made out of plastic and it is sold individually. You will need a wrench to remove the carburetor when replacing this item.

It is an authentic component that is supplied by the original equipment manufacturer for use with Homelite and Ryobi handheld string trimmers. This is an identical replacement for a missing or a faulty handle bar clamp that was installed on a new unit. The part is utilized to secure the handle bar. Please make sure to refer to the appropr...Read moreiate diagrams of your model for the correct location and application of this component. Keep in mind this high-quality clamp is made of durable metal and is sold individually.