B59FN-5TVW Magic Chef Range - Overview
Sections of the B59FN-5TVW
[Viewing 2 of 2]
Keep searches simple, eg. "belt" or "pump".
Light Bulb - 40W
PartSelect #: PS884734
Manufacturer #: 8009
This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these replacement bulbs are mos...
$19.54
In Stock
Long Oven Sensor
PartSelect #: PS1570174
Manufacturer #: 12001656
This long oven sensor is also commonly known as a temperature sensor. It is designed for use with ovens and ranges. It is similar to a thermostat; it measures and regulates the internal temperature of...
$43.18
In Stock
2 Piece Broiler Pan
PartSelect #: PS971245
Manufacturer #: 4396923
This broiler pan and roasting rack set is designed to help reduce mess while cooking by allowing grease to drain away from food. Its durable porcelain-coated construction stands up to high temperature...
$49.50
In Stock
Bake Element (15 Inch long x 19 Inch wide)
PartSelect #: PS11757468
Manufacturer #: WPY04000041
This spade style bake element with push on wire terminals is 15 inches long and 19 inches wide. The depth of the terminals is three inches.
$79.80
In Stock
Clock Knob - black
PartSelect #: PS11744674
Manufacturer #: WP7711P492-60
The clock knob attaches to the center of the oven control panel and is used to adjust the built-in clock. This clock knob is less than an inch in diameter. It is all black in color and is made of plas...
$17.15
In Stock
Range Frame Screw
PartSelect #: PS11743908
Manufacturer #: WP7101P126-60
Sold Individually.
$7.47
In Stock
Oven Rack
PartSelect #: PS1656457
Manufacturer #: 7801P030-60
Sold individually.
No Longer Available
Door Glass Spacer
PartSelect #: PS1646197
Manufacturer #: 74003986
Sold individually.
$23.60
Special Order
Broiler Pan
PartSelect #: PS11741639
Manufacturer #: WP3401F075-19
This broil pan is fourteen inches wide, and almost sixteen inches long. It is made of black porcelain.
No Longer Available
Range Nut Snap
PartSelect #: PS11743921
Manufacturer #: WP7103P114-60
This is an OEM part sourced directly from the manufacturer. This snap nut is round, and is made of black plastic. It is approximately half an inch in diameter. This snap nut should snap into place, ra...
$11.77
In Stock
Common Symptoms of the B59FN-5TVW
[Viewing 9 of 9]Little to no heat when baking
Fixed by
these parts
these parts
Show All
Oven is too hot
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Touchpad does not respond
Fixed by
these parts
these parts
Show All
Will not program
Fixed by
these parts
these parts
Show All
Door won’t open after self cleaning cycle
Fixed by
these parts
these parts
Show All
Little to no heat when broiling
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven not holding 350 F, when cooling the coils did not reheat
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening,
... Read more
reinstall 2 screws. The oven works fine! Note that due to thermal lag the temperature overshoots to 370 degrees and undershoots to 340 degrees, this appears to be normal oven operation. Putting door back in place was easy.
Read less
Parts Used:
-
David from Westford, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
162 of 213 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
F1-1 code
First I removed the two screws that hold the element in place. I then pulled the sensor out about 3 inches and disconnected the two wires. Next, I connected new sensor and screwed the new sensor back in place. One area for caution. Make sure that the electrical connection is pushed in past the insulation on the back side of the oven. Fa
... Read more
ilure to do so will cause the plastic plug connector to melt from oven heat.
Read less
Parts Used:
-
charles from marstons mills, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
79 of 110 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Repeated oven temperature sensor fault codes.
First I removed the two philips screws inside the oven that hold the element in place. Then I pulled the sensor out and the two insulated wires through the hole to reveal the plastic connector. I unsnapped it from the connector and replaced it with the new element. Then, behind the oven, I removed five or six philips screws on the righ
... Read more
t side of the large panel so I could pull the wires back through the layer of fiberglass insulation to make sure only the sensor itself would be exposed to the oven's heat. I then secured the back panel again and replaced the two philips screws holding the sensor in place.
Read less
Parts Used:
-
David from Arlington, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
35 of 43 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!