AYP8 Husqvarna - Overview

The OEM bearing, also known as the flange bearing, is silver, made of metal, and sold individually. It is used on riding mowers to secure the wheel in place and allow it to rotate freely on the shaft. Over time, the part may become worn and damaged, which you will notice if you experience a squealing or grinding sound from the wheel in qu...Read moreestion, or you notice the wheel is sloppy on the shaft. You will need a hammer and punch to complete this repair, which most of our customers rated as easy. Make sure you tap the new bearing into place evenly inside the tire rim.

The Ring Klip Number T5304-75, also known simply as a ring clip, is an OEM part designed to secure your mower wheel to its axle. This part is black, made of metal, and around an inch in length. It is sold individually and may become damaged over time due to wear and fatigue.

This OEM washer, also known as a flat washer, has dimensions of 25/32 x 1-1/4. Silver in color and metal, the washer is sold individually. Although this part can have a range of applications depending on the equipment, its general function is to spread the load under a bolt. Ensure you consult your owners manual or check your model number...Read more to confirm this is the washer you need for your equipment. This part will need to be replaced when your existing one is worn or damaged. It is an easy repair according to our customers, and does not require any special tools.

This hairpin clip, also known as a cotter pin, is a genuine OEM sourced part used to secure rotating components together in various outdoor power equipment. It is made of steel and is approximately 1.5 inches long. The clip acts as a fastener to prevent the moving parts from loosening and falling off during usage. The clip is vulnerable t...Read moreo corrosion and general wear over time. However, it can also fail prematurely due to overloading and excessive stress. A damaged hairpin clip will result in misalignment of parts, accidental disassembly, increased friction and wear, and potential harm to the user. Remove the faulty pin and align the new one with the insertion points. Ensure that the pin is securely fitted in its appropriate slot and compress the ends to prevent it from dislodging.

Genuine Husqvarna replacement part, this item is sold individually. This bearing is installed on top of the shaft which is encased in the mandrel assembly. The mandrel assembly is bolted to the mower deck. The shaft of the mandrel assembly is what the blade on all of the riding mowers listed below is attached to.

This is a genuine replacement part sourced directly from the original manufacturer. This assembly consists of metal parts and it is sold individually. This is the part that houses shaft that mower blade attaches to, it is mounted to the deck of the mower by three (3) bolts (sold separately). Please note that the mounting holes on mandrel...Read more housing are not threaded. Bolts that are used to secure the mandrel to the deck are self tapping. When doing this repair you would need a set of wrenches. • First remove the blade from the mandrel shaft • Remove the three (3) screws that are holding mandrel to the Deck • Then, you will need to remove the nut that is attached to the mandrel shaft, which is located above the mandrel pulley. The complete mandrel assembly should come right out now. • Attach the new mandrel assembly back to the deck • Attach and secure pulleys, belts and blades

This is a genuine OEM part made for Craftsman lawn tractors and mowers. Bearings are used to buffer moving parts from damage due to friction. They also stabilize directional movement. Bearings are high-wear parts and are changed regularly. This metal bearing is sold individually. Gauges, washers, rings, etc. sold separately.

The Push Nut is a black, metal nut, which can be installed with pliers and a hammer. It's used to secure parts in place in various locations on a variety of equipment. If damaged will not longer hold in place. Installation is rated as "Easy", but it will depend on the parts your are securing and the equipment you are using. Consult your m...Read moreake, model and diagrams to ensure this is the correct part. The part is sold individually.

This is a genuine replacement belt sourced directly from the original manufacturer, designed for use with riding lawn tractors and mowers. Made from durable rubber and sold individually, this belt is responsible for driving the mower blades, making it a critical component for cutting performance. To ensure optimal function and longevity, ...Read moreit’s important to clean the pulleys before installing the new belt and to inspect the belt regularly for signs of wear or stretching. Replacing the belt requires a wrench set and pliers. For safety, always disconnect the spark plug wire before beginning. Start by lowering the mower deck to its lowest position and setting the blade engagement lever to the "Off" position. Roll the old belt off the engine pulley from between the belt guide and pulley. Remove the mower deck by taking out the bow-tie pins securing the left and right lift arms, then disconnect the blade engagement cable. Next, remove the bolts from the mower deck belt pulley covers and take off the covers. Loosen, but do not remove, the nuts on the top of the idler pulleys. Install the new mower deck belt through the belt guides and around the pulleys, then tighten the idler pulley nuts. Finally, reassemble the deck to complete the repair and restore your mower’s cutting performance. Lawn mower deck belt. Width: 1/2 " Length: 95 1/2 ".

This OEM-certified washer provides support, spacing, and reduces friction between parts in your lawn equipment, typically working alongside bolts or screws. This washer has a thickness of 16 gauge and dimensions of 25/32 x 1-5/8 inches. A damaged washer will look deformed or cracked, leading to parts becoming loose or not fitting properly...Read more in your machine. When you remove a broken washer from your machine, you will need pliers or a wrench to loosen the bolt or screw securing it. Once the fastener has been removed, you can pry the washer with a screwdriver. It is important to know that this washer is sold individually. Before adding this replacement part into your cart, check your instruction manual to determine the number of washers your machine needs.

This is a Genuine OEM replacement part used on Ride Mowers/Lawn Tractors. This is the Wheel that helps to support the Deck and allows it to move around easier. This Wheel is made out of Plastic and it is Sold Individually. Please note the Bolt and Nut used to secure this Wheel are Sold Separately. To replace this item you would need a Wrench.

This is an original part from Husqvarna. The hood latch is constructed of flexible plastic, and is made for use with many riding lawn mowers. This component is fastened onto the lower bagger chute, latching it to the upper chute. The hood latch is sold individually. A pair of pliers and a screwdriver may be helpful for the removal and replacement.