EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

AWS75NW Speed Queen Washer - Overview

Diagrams for AWS75NW

See every part. Know exactly what you need.

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Retaining Ring – Part Number: WP23748
$12.85
In Stock
Retaining Ring
Part #WP23748
The metal retaining ring, which is under an inch long, holds the rear wheels on the axels of the dryer. The main reason why it would need to replaced is if the retaining ring has sprung out of place or is damaged. Some the symptoms could be that your dryer does not tumble, it makes a loud buzzing noise, or if it pumps, but will not spin. The tools needed for this project are a putty knife, 5/16 nut driver, and snap ring pliers. Refer to the installation video and diagram for further instructions and guidance. Customers ranked this replacement project as easy.
Thrust – Part Number: WPW10121334
$7.47
In Stock
V-Style Spin and Agitate Belt - 28-3/4 inches long – Part Number: WP27001006
$43.18
In Stock
V-Style Spin and Agitate Belt - 28-3/4 inches long
★★★★★
★★★★★
(3)
Part #WP27001006
This v-style spin and agitate belt is 28-3/4 inches long and half of an inch wide. It is all black in color and made entirely of rubber.
Lid Hinge Mounting Screw – Part Number: WPW10119828
$7.47
In Stock
Lid Hinge Mounting Screw
★★★★★
★★★★★
(2)
Part #WPW10119828
Sold individually. NOTE: The color on the screw may not be the same as the image, but will still function the same.
Drain Hose with Rubber Elbow – Part Number: WP40053901
$55.29
In Stock
Drain Hose with Rubber Elbow
★★★★★
★★★★★
(4)
Part #WP40053901
This hose attaches to the pump to help remove the water out of the washer. 7 feet in length.
Washer Inlet Hose Washer – Part Number: WPY013783
No Longer Available
Washer Inlet Hose Washer
★★★★★
★★★★★
(1)
Part #WPY013783
This inlet hose washer, also known as a high pressure inlet hose washer, is used in washing machines, refrigerators, freezers, and dishwashers. The function of this part is to create a watertight seal in the appliance. If your gasket gets dry and brittle over time it will start to crack and will lose its function. In this case, it is important to replace it. Refer to the manual provided by the manufacturer for further installation instructions and accurate guidance. As a safety precaution, remember to unplug your washer from the power source before beginning.
Drive Bell and Seal Kit – Part Number: R9900189
No Longer Available
Drive Bell and Seal Kit
Part #R9900189
This washing machine drive bell and seal kit comes with a seal, a plug, a shoulder screw, a drive bell, and some grease.
Refrigerator Screw – Part Number: WP489128
$11.77
In Stock
Refrigerator Screw
Part #WP489128
This screw is sold individually.
Single Washer Inlet Strainer – Part Number: WP22002960
No Longer Available
Single Washer Inlet Strainer
Part #WP22002960
Found at the end of the inlet hoses.
Selector/Rotary Knob – Part Number: WP36701W
$49.50
In Stock
Selector/Rotary Knob
Part #WP36701W
This knob accepts a D-shaped shaft.
Screw – Part Number: WP27001200
$7.47
In Stock
Screw
Part #WP27001200
Sold individually.
Standpipe Adapter – Part Number: 40008101
$53.20
Special Order
Standpipe Adapter
★★★★★
★★★★★
(1)
Part #40008101
This part helps stop the washer from overflowing.

Common Symptoms of the AWS75NW

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Water leaking on floor from "mysterious place underneath washer"
51 of 57 people found this instruction helpful.
  • Bryan from Chicago, IL
  • Easy
  • Less than 15 mins
  • Pliers, Socket set
Water was leaking on the floor during the wash cycle and especially during draining of the washer. I removed the front panel at ground level and watched while draining after a rinse.

I t was obvious that water was spraying from a hole in the rubber end of the hose (the hose is a fused assembly of a plastic section and a rubber section).

So, I finished draining, removed the hose (required pliers to squeeze off a hose clamp).

Upon inspecting the hose, it was also apparent that the hole was caused by rubbing against a support bracket for the motor. This should not happen, but it did because the plastic standoff supposed to keep the hose away from the bracket was installed 180 degrees backwards.

So, I simply replaced the hose and turned the bracket around to the correct orientation.

Everything worked as planned and my repair cost was much less than if I had called someone out.
Was this helpful?
Thank you for voting!
The thin walled plastic drain line got a pin hole leak
9 of 10 people found this instruction helpful.
  • WALTER from Holualoa, Hawaii, AL
  • Really Easy
  • 15 - 30 mins
  • Pliers, Wrench set
The washer is four years old.
This is the second time I needed to replace this same drain hose on this same washer since I had the machine
There is only my wife ant myself maybe, 2 -3 medium size loads per week - why I would have two drain lines develop the same problem in almost the same location in two years is disconcerting
There must be a design problem with the clear plastic hose - Suggest Maytag go to a thick walled rubber hose
The hole is alway inside the washer on the bottom just after the hose bracket - I suspect that something rubbing causing a small pin hole to develop - when the condition first starts it is very difficult to located -There will be water under the washer
Run the washer and discharge the water - to locate

The replacement must be made through the lower front removable panel - and is easier to do if the pump return hose is also disconnected from the pump

Be very carful with the thin wall replacement hose - very light weight plastic - do not pull across the floor of washer - it could easily get damaged

Your company did a get job getting the part to me - The Fed Ex track system was great
I could tell exactly where the delivery was al all times -
Was this helpful?
Thank you for voting!
replace rubber drain hose adapter
7 of 11 people found this instruction helpful.
  • Frank from Austin, TX
  • Easy
  • Less than 15 mins
Place black rubber adapter on the end of the drain hose and stick in the stand pipe drain. That's all.
Was this helpful?
Thank you for voting!