Quick Question!

Have you ever purchased from PartSelect.com before?

Models > AWP330G1W

AWP330G1W Kelvinator Washer - Overview

Get Parts and Repair Help for AWP330G1W

If you know the washer repair part you need, you can browse the list of all parts on the AWP330G1W, or you can search by name or part description. You can also find your part by where it is located on the AWP330G1W by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$25.28

Snubber Ring

The snubber ring on your washing machine mounts at the base, under the support. If you notice that your washing machine is vibrating, shaking, or moving during the wash cycle, you ...

$9.20

SPACER

This spacer is used in washers or a washer and dryer combo unit. Spacers are used to create space between cotter pins, lock nuts, hitch pins or to fill the space between machinery parts in a washer. This part goes between the timer knob and the dial in a washer to function effectively and provide protection. The length of this part is 6.35 inches with a width of 5.25. The spacer has a height of 8.125 inches and the weight of 0.3 pounds. Refer to the manual provided by the manufacturer for further installation instructions and guidance. Remember to unplug your appliance from the power source.

$8.72

Touch Up Paint - White

This is white touch up paint for refrigerators, microwaves, ranges, dryers, and freezers. It is used to cover, or touch up, nicks and scratches on the appliance from wear and tear....

$8.72

Upper Spin Bearing Washer

The upper spin bearing for a washer can solve many issues such as loud and odd noises, or leaking water. Replacing the spin bearing could solve these issues. The tools needed for this replacement are screwdrivers, a socket set, and a putty knife. To repair, first lift the top of the washer and remove the screws at the bottom of the front panel to pull away. Next, pull off the dispenser cover, cup, and agitator. Detach switch tube from the tub cover and remove tub cover, then use the 1/2 inch socket to remove the trunnion bolts and pull out inner tub. For the rest of the installation instructions, refer to the diagram provided by the manufacturer. Remember to unplug the appliance from the power source as a safety precaution.

$5.29

Single Tub Cover Clip

$8.72

SPRING

$16.30

V-Style Belt

This v-style belt or drive belt is designed for use in your washing machine. This part connects the drive motor to the drive system in the washer, which spins the basket. If you no...

$16.20

Levelling Leg Pad

Sold Individually.

$13.35

Trunnion Plate

Locking Plate.

$10.02

BOLT

Holds plated on Trunion .312-18 x 1.625.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Leaking washing machine.

  • Customer: Ron from Williamsburg, MI
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Socket set
  • 23 of 35 people found this instruction helpful
Removing the piece above the tub gasket was very difficult. A lot of hammer and chisel work.
15 year old machine. A lot of calcium build up around the shaft. I used a screw driver as a chisel and a hammer. Carefully removed the metal around the shaft to get to the tub seal.
Once I got to the tub seal it was easy. Remove the old rubber stops.... read more

belt worn causing machine to make all kinds of noise

  • Customer: Kenneth from Baltimore, MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 18 of 25 people found this instruction helpful
pull up on top ,take two screws loose on front panel(pull off) vaccum old debri out,pull tension pulley back pull old belt off,holding tension pulley put new belt on .put front panel back on and snap top back down to secure.
working perfectly nice and quite !!! read more

drive belt replacement

  • Customer: Scott from Cumming, GA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 4 of 5 people found this instruction helpful
removed rear panel, tilted machine forward, removed four bolts holding the pump and loosened the connection to the motor shaft,(several times dropped socket and without magnet to retrieve tools would have been much more difficult),removed two hoses, dropped pump assembly, replaced belt, and reversed the process to re-assemble. Easy to find part and will defi... read more