AST-5000 Tanaka Trimmer - Overview

The fuel pipe/fuel line assembly is a genuine OEM parts kit used in gas-powered outdoor equipment with dimensions of 5mm x 160mm. It includes a pipe or line, which carries fuel from the tank to the carburetor, and a rubber grommet which holds the fuel line in place. The grommet also has a flange that prevents it from being pulled into the...Read more body of your equipment. Over time the grommet may wear down and the fuel line can become brittle and crack causing fuel leakages and difficulty starting or running your equipment. Therefore, it is important to routinely inspect this assembly and replace it when it shows signs of wear. Before your repair, drain the fuel for your safety and to prevent contaminating the fuel tank. To install a new fuel pipe assembly, simply pull off the old grommet and detach the fuel line. Carefully insert your new fuel line into the new grommet and connect the line to the carburetor and the fuel filter inside the fuel tank on your equipment.

Also known as a priming bulb, this OEM replacement part is an individually sold rubber primer bulb. Since it is made of rubber, it will eventually lose its elasticity and crack or break,and need replacing. It is designed for use with a variety of different small engine equipment and is also known as a purge bulb. Pressing this primer bulb...Read more forces fuel through the fuel line and into the carburetor from the fuel tank. Once the carburetor is has a sufficient level of fuel, any excess fuel will be forced back into the fuel tank through the return line attached to the carburetor. If your primer bulb has a darker appearance or has lost its elasticity and does not return to its original shape, it means the rubber will likely soon crack, which will lead to fuel leaking into the engine and ignition system. To replace your primer bulb, simply remove the outside cover and primer bulb cover and replace the bulb within its housing.

This is a genuine OEM replacement part, it is sold individually. The Fuel Filter is inside of the fuel tank. Its purpose is to filter out dirt and other debris from contaminating the carburetor. It will at sometime become clogged and restrict the fuel getting to the carburetor,and will have to be replaced. We do have an article and vide...Read moreo on How to Replace the Fuel Filters in Your Outdoor Power Equipment.. You can see this by going to the front page of our site and clicking on Repair Center.

This item has been OEM sourced to ensure a high level of quality. The clip is intended to be used with trimmers and blowers from Hitachi and Tanaka. The metal clip is part of the fuel system. The clip is used to fasten the fuel filter and the fuel line assembly. This part is priced as an individual replacement part.

This is a genuine Tanaka part for use with Trimmers and Edgers. The throttle lever allows you to control engine speed. The most common reason for replacing the throttle lever is if it is damaged or not engaging the throttle properly. This part is sold individually. The tools that you will need to replace the throttle lever is a T-25 Torx head screwdriver and a flat-head screwdriver.

This is a genuine Tanaka replacement part, sourced directly from the manufacturer. The oil seal is found in many Tanaka power tools such as chainsaws and brush cutters. This part is a metal ring with a high-quality plastic inner ring, and is used to prevent oil leaks or contamination of the crank case. You may need a screwdriver and wrench to replace this part. This item is sold individually.

It is a genuine OEM supplied replacement grommet that is specially made for Tanaka gas powered equipment. This grommet is connected to the fuel hose helping to secure it and preventing any leaks. Over time it may deteriorate and crack eventually requiring replacement to maintain air-tight seal. It is made from high-quality rubber material and it is sold individually.

This authentic component is supplied directly from the original equipment manufacturer for use with Tanaka lawn and garden equipment. The cap is used to connect the spark plug to the magneto. It provides an identical replacement for a missing or a faulty part that was installed on a new unit. Please make sure to refer to the appropriate d...Read moreiagrams of your model for the correct location and application of this cap spark plug assembly. Keep in mind one durable rubber cap and a metal spring are included.

This item is a genuine Tanaka replacement part that is OEM sourced and intended to be used with trimmers, brushcutters, edgers, and power augers. The metal spark arrested attaches to the muffler's tail-pipe and is used to reduce sparks from exiting with the exhaust. A Phillip's head screwdriver may be needed to install the spark arrester and this part is sold individually.

This is a genuine manufacturer-sourced replacement part which is designed for use with Tanaka handheld trimmers. The purpose of the eyelet is to let the cutting line out of the spool assembly without damaging the part of the housing the eyelet is installed in. It also allows the cutting line to exit the spool smoothly without being cut. I...Read moret is made of high-quality metal and is sold individually. No tools would be needed to replace this eyelet. Simply insert into the opening of the spool housing.

This is a genuine replacement part sourced from the original manufacturer for use with bicycle engines made by Tanaka. The user will need to replace this small washer if it is missing or not working correctly. This part is made of durable material and sold individually.