This door closing cam kit is intended for use on the bottom of your refrigerator and freezer door hinges. The cam helps close the doors and to lifts them slightly when opened. If your door will not open or close, or will not stay closed, there could be an issue with the door close cam. Other common symptoms associated with the door close ...Read morecam are: the door is sweating, the fridge is too warm, or a clicking sound can be heard coming from the door. If your refrigerator has an ice and water dispenser, you will need to disconnect the power and water to the unit before you begin the repair.
This helix end cap is almost four inches in diameter. It is all white in color and is made of plastic. This end cap is used in a refrigerator's icemaker.
This is the replacement ice maker auger and crusher blade assembly for your refrigerator. It is approximately 15 inches long and 7 inches wide. The ice maker auger sits within the ice maker assembly and rotates to push the ice from ice container into the dispenser chute. If your ice maker bucket is full, but ice is not being dispensed, it...Read more is an indication that the auger is damaged. Be sure to disconnect power from the refrigerator before you repair the auger. This part is sold individually and is an authentic OEM part sourced directly from the manufacturer.
The compression nut is used as a connection between the water supply line and other components in your refrigerator such as your ice maker and your water dispenser. Tools required for this repair include a pair of pliers and a socket set. Before installing this part you should take all perishable foods out of your refrigerator and store t...Read morehem somewhere cool, unplug the refrigerator from the power source, and shut off the water supply. This repair may require you to wear work gloves to protect your hands, and is considered an easy do-it-yourself fix.
This part is the replacement shelf support for your refrigerator/freezer. It is made of white plastic and is approximately 1 inch by 1 inch. The shelf support attaches to the side of your refrigerator wall and supports the shelf. If your shelf is sagging or will not stay in place, you may need to replace the support. To replace the suppor...Read moret, use a wrench to turn the support clockwise until you can use a flat blade screwdriver to pop it out. Push the new support into the hole left by the old one until it is flush with the liner, then use the wrench to turn it clockwise until it locks in. This part is sold individually and is and OEM part.
This part supplies water to refrigerator components that require water, such as the ice maker and water dispenser. If you notice a leak coming from your refrigerator, the plastic tubing that feeds your water and ice dispenser might need to be replaced. This part is made of clear plastic and is 1/4 inch thick, and 8 1/2 feet long. Make sur...Read moree to disconnect power to the refrigerator and shut off the water supply prior to installing this part. Safely store any perishable food items that could deteriorate while the power to the refrigerator is disconnected. Work gloves are recommended to protect your hands during this installation.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Door would not close
79 of 84 peoplefound this instruction helpful.
Russ from Asheville, NC
Easy
15 - 30 mins
Nutdriver, Screw drivers
After emptying the refrig. door, I unscrewed the plate on the top of the refrigerator that covered the door bolts. Then off with the three bolts. I removed the door by lifting it up a few inches. The two parts of the door cam were easily removed and replaced with the new part. BEFORE REPLACING the door spread vasoline on both cam parts.
... Read more (Not after as I did. The second time you do any of these repairs go SO much better :o) After putting the door back on, adjust the tension of the screws holding the door in place if needed to align the door on the cams so that it shuts completely. Failure to do this will require taking the top off the door again. (see comment above on "... second time...") If all is properly aligned, the door should swing completely shut. Even with the mistakes that required removing the door to lubricate the cams, and removing it AGAIN to readjust the screws on the top to properly align the door on the cams, this was a twenty minute job. My wife and I were still speaking to one another at the end of it- a sure sign of an easy repair.
Read less
Was this helpful?
Thank you for voting!
Ice Dispenser had jammed up and become inoperative
40 of 47 peoplefound this instruction helpful.
James from Robinson, TX
Easy
15 - 30 mins
Screw drivers
The parts discription was a bit vague and I wasn't sure exactly what I was ordering, but I received everything I needed and it works fine. The combination screw conveyor/ice crusher came in one piece. The ice cube bin is a plastic assembly that snaps apart. I used a wide blade screw driver carefully to facilitate assembly/disassembly.
... Read more Once you have it apart the old converyor slips out and the new one slides in. Do not remove the two screws that hold the new assembly together. You need a phillips scredriver to take out two of the screws from the old assembly and put in the new one. That is, there are four screws and you need to trasfer two of them. Everything now works fine.
Read less
Was this helpful?
Thank you for voting!
Door cam worn out
27 of 29 peoplefound this instruction helpful.
william from avon, OH
Really Easy
30 - 60 mins
Screw drivers, Socket set
remove top plastic cover / phillips screw driver remove top door bracket / 5/15" socket lift off door remove pieces of old cam / phillips screw driver replace cam/ phillips screw driver replace door replace top bracket / 5/16" socket check alignment