This is a surface burner igniter, also known as a top burner ignitor and stove top spark electrode. It is used to generate the spark that lights the surface burner. If your stove will not start, element does not heat, or gas igniter glows but does not light, replacing the igniter can solve these issues. For this installation, you will nee...Read mored a Phillips screwdriver and needle nose pliers. First place the grate on top of the burner, then lift the burner and disconnect the wires. Next remove the two Phillips screws from the bottom of burner, pull igniter out of the burner and wiggle in the new one. Refer to the installation instructions provided by the manufacturer for more instructions.
This burner cap assembly is sold with the spark electrode igniter and has a 7-inch outer diameter. This manufacturer-approved surface burner is for gas ranges. The surface burner supplies the heat to a cooking area on the cooktop. You may need to replace your burner cap if the gas igniter glows but will ignite the flame, the range will no...Read moret start, or if you can smell gas. Because a faulty burner cap could lead to a house fire, it is recommended that you replace this part as soon as you realize it is faulty. Remember to unplug the range, turn off the gas, and let the unit cool down before starting this installation.
Note: this part has been redesigned and no longer requires a gasket, and is sold individually.
The glass clip for your oven helps to hold the exterior glass in place. If you notice that your exterior glass is askew, or will not stay in place, you may need to replace the glass clip. This clip is just over an inch in height, and 1 inch in width. This part is made of black plastic and is square on the bottom, but triangular on the top...Read more. This is an OEM part sourced directly from the manufacturer. This product is sold individually. When ordering you will have to enter the order quantity.
This thermostat clip, used in ranges and ovens, secures the thermostat bulb. Without this clip, the bulb is left without support and this keeps the thermostat from functioning properly. *Please note: this part is sold individually. If your clip is broken or damaged, replacing it could solve your problem. Please refer to the manual provide...Read mored by the manufacturer for further installation instructions and accurate guidance. As a safety precaution, make sure to unplug your range from the power source.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
A burner wouldn't spark strongly enough to light the gas.
168 of 188 peoplefound this instruction helpful.
Matthew from Brookfield, MA
Really Easy
Less than 15 mins
Pliers
Replacement of these burners is very easy. You just twist the burner counterclockwise a quarter turn and pull it out. (You may need a big wrench if the range is very old.) Once out, just pull the two wires off and push them onto the new burner. Crimp them on with pliers if they're loose -- mine were. Twist the burner back on. If the
... Read more gasket under the burner has disintegrated, don't worry about it. They don't offer replacements for them because they're not necessary as a safety feature. They were designed to keep overspills from running under the cooktop, but the ridge around the hole is likely higher than you'd ever need.
Read less
Was this helpful?
Thank you for voting!
gas burner ignitor failure
142 of 162 peoplefound this instruction helpful.
roy from East Providence, RI
Easy
15 - 30 mins
Screw drivers
Lift out sealed burner assembly rear of stove first while careully sliding to rear to disengage ignitor probes.Remove philips head screws from bottom sheet metal housing to expose bottom of burners Remove gas tube assembly screws and move tube away carefully.Unplug wires from ignitor.Remove screws for ignitor .Remove ignitor, I noticed t
... Read morehat rust and dirt had built up around burner to pan connection.I used my oil filter wrench to turn slightly the burner to remove it from the pan to clean.Reassembled in reverse order.
Read less
Was this helpful?
Thank you for voting!
Burner Was Worn Out
31 of 32 peoplefound this instruction helpful.
arnold from la punte, CA
Really Easy
Less than 15 mins
Screw drivers
Burner head arrived when I got home from work. Just timely to cook for dinner that monday night, got the 4 burners disconnect the element from the old burner, then connect element to the new bunners, in less than 10 mins, and I had save estimate $600 buying a brand new stove or gas range, this will last me another5 to 10 years. Espec
... Read moreially this time of recession