This broiler pan and roasting rack set is designed to help reduce mess while cooking by allowing grease to drain away from food. Its durable porcelain-coated construction stands up to high temperatures and makes cleanup simple. With approximate dimensions of 16 3/4 inches long, 12 3/4 inches wide, and 1 3/4 inches high, it offers a convenient size for everyday broiling and roasting.
The temperature sensor is a part for the oven, on your range. This temperature sensor has a body length of just over 3 inches. The purpose of this part is to measure the temperature within the oven and report it back to the control board where it can be displayed. To make this repair you will need a number two Phillips screwdriver or a nu...Read morember two square-head screwdriver. To replace this part, you will need access to the back of the range. This means you will need to pull the range away from the wall, disconnect the power, and remove the back panel.
This spark ignition module lights the gas that starts the burner on your range or cooktop. This electrode is part of the burner assembly, sits next to the burner head, and is just over an inch in length. It pulls current from the ignition circuit; the more current it pulls, the warmer it gets. When the spark ignition module reaches a cert...Read moreain temperature, it creates a spark. This spark ignition module comes with the mounting bracket you will need to successfully install the part. Before installing your new part, ensure that the gas supply and power is disconnected from your range. This part cannot be repaired. If it is damaged or faulty, it must be replaced.
The hinge kit, or oven door hinge, is used in ranges and wall ovens. The hinge attaches to the right side of the door and controls how fast the door opens. At a specific angle, it allows the door to remain open. If you are having trouble opening and closing your door, or it does not close at all, replacing the hinge could solve your probl...Read moreem. The hinge is made from metal and the kit comes with the hardware needed for this installation. You will need a screwdriver to perform this repair. *Please note: This part is only for the right side of your appliance. The left side is sold separately.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Getting F 1 and 2 error codes and the oven turned itself off.
76 of 144 peoplefound this instruction helpful.
Suzanne from Acton, MA
A Bit Difficult
Less than 15 mins
Screw drivers
Really easy but in this model there are 2 versions of the sensor, male and female. The website didn't have any place to see that. So the first sensor that came was male but we needed the other. After calling they sent me a return form and sent the new part (which was actually much cheaper) overnight and it went in very quickly. Would che
... Read moreck this out again when anything went wrong. they are great folks to work with.
Read less
Was this helpful?
Thank you for voting!
2 of 4 burners wouldn't light
25 of 29 peoplefound this instruction helpful.
John from Alexandria, VA
Really Easy
Less than 15 mins
Screw drivers
Unplugged the stove, removed all 4 burner discs from the stove top (2 screws each) and disconnecting electrode wires as I pulled them out, removed the stove top, unscrewed the old module, removed the 6 wires, connected wires to the new module, screwed it into place, reinstalled the top while poking the electrode wires through the top one
... Read more by one, put the stove top in place, connected the wires to the burner discs. Done, and it works! It took longer to find and order the part than it did to change it out.
Read less
Was this helpful?
Thank you for voting!
There was a crack in the porcelain not letting it spark
23 of 36 peoplefound this instruction helpful.
Billy from Martinsville, IN
Really Easy
Less than 15 mins
Screw drivers
I used a screwdriver to pry the electrode assy. out of the burner. then disconnected the wire. Then just connected the new electrode and place the assy, in the burner.