This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch. It has 6 threads. Refer to the manual provided by the manufacturer for further information on repair and accurate guidance. Remember to wear work gloves as a safety precaution.
This is an OEM part that is made of metal and sold individually. The leveling leg is generally used with refrigerators, dryers, freezers, ranges, cooktops, and microwaves. The leveling leg is meant to keep your appliance steady and level to the floor. If you notice your appliance is uneven to the floor it may need to have the leveling leg...Read more replaced. You will notice that the bottom of the leveling leg has a smooth surface to ensure moving your appliance does not require as much effort. This part screws into a pre-drilled hole underneath the appliance.
The door gasket is used on vertical freezers. Screws are no longer included with this product. The gasket creates a tight closure around the opening of the door to ensure that outside air does not enter the freezer, causing it to warm up. If you notice that your freezer is not closing properly, is not maintaining the proper temperature, o...Read morer there is frost build up, it could be due to the breakdown of the door gasket. It is white in color. This is an easy repair that should not take longer than 60 minutes and only requires a nutdriver to fix.
This defrost heater part number W11175809) is for refrigeration appliances.
The defrost heater melts frost from the evaporator fins during the automatic defrost cycle.
Safely store any food that could deteriorate while the power is off and unplug the appliance before installing this part. Wear work gloves to protect your hands.
This part is a temperature sensing devise. It senses the rise in evaporator temperature during a defrost cycle and cycles the defrost heater off after all frost is melted. It is calibrated to permit a defrost cycle only when the temperature is below a preset temperature
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
gasket had harden. frost was building up quickly
27 of 33 peoplefound this instruction helpful.
LESLIE from TAPPAHANNOCK, VA
Easy
30 - 60 mins
Nutdriver
the gasket peels back to reveal the approx 20 screwsholding gasket and door shelves. removed these. removed old gasket from door panel. new gasket needs to be stretched to get on door panel. align screw holes in door panel with screw holes in gasket. attached back to freezer door. this gasket did not seal securely when closing door.
... Read more this gasket was installed on a cold day in a garage and may become more flexible as it warms up.
Read less
Was this helpful?
Thank you for voting!
Frozen items on top of freezer not quite frozen, bottom of freezer ok. Freezer alarm sounding.
27 of 42 peoplefound this instruction helpful.
Randall from Burlington, WI
Easy
30 - 60 mins
Nutdriver, Screw drivers
Disconnect power / Remove shelves / remove sheet metal panel in rear of freezer / disconnect fan wires / remove fan unit using nut driver. / reassemble.
Was this helpful?
Thank you for voting!
Fault in defrost circuit caused ice buid-up, decreased air flow, and elevated temp. led to a thaw.
15 of 19 peoplefound this instruction helpful.
Dennis from White Bear Lake, MN
Really Easy
15 - 30 mins
Screw drivers
After observing defrost timer go into (and out of), defrost cycle, I checked continuity of heating element. Since heater coil was intact (79 Ohms of resistance), I figured the defrost thermostat (aka bi-metal therm.), had to be at fault. The new part ($17.00), proved my suspicions correct. As I sought to determine if everything worked, I
... Read morehad to wait for the temp. to drop below the defrost therm. set point before I would see the heater coil get hot. To avoid the costly failure in future, I bought a Chaney wireless therometer with two remote sensors. Sensors require lithium batteries. $30.00 for both are a cheap insurance system.