AEQ7000CES1 Frigidaire Dryer - Overview

This rear drum bearing kit is designed for use with dryers. It supports the rear of the drum in your appliance as it tumbles your clothes during the drying cycle. If your drum will not tumble, or if it is making a lot of noise, it could be an issue with this part. This is a ball-and-socket style bearing. You will need to replace this if t...Read morehe bushing has worn out, or if the ball support is damaged. This kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant and installation screws. Unplug your dryer before you begin this repair.

This drum belt, often referred to as a drive belt, is used in the assembly of dryers. It goes around the drum, the idler pulley, and the motor pulley. As the armature on the motor spins, this belt is what rotates the drum and tumbles your clothes during the dry cycle. If you can hear the motor running but the drum is not moving, that is a...Read more sign your belt is broken, stretched, or damaged, and can no longer grip the drum. This belt is 88 3/4 inches long, and is 1/4 inch wide. Because it is made of rubber it is common for this part to become brittle and need to be replaced. This is an authentic OEM replacement part, and it is sold individually. Remember to unplug your dryer before you begin this repair.

If your dryer does not tumble, will not start, is noisy, or is leaving marks on your clothing, you may need to replace the drum support bearing. The drum is supported at the rear by a bearing, which attaches onto the inside of the rear panel of the cabinet. You will need to remove the dryer drum before completing this repair. Although rep...Read morelacing the drum support bearing is a fairly easy job, you will need tools to complete it. For this repair, you will need a putty knife, a Phillips screw driver, a 5/16 nut driver and maybe a small flat blade screw driver.

This white drum glide is used in a clothes dryer to ensure the front of the dryer drum is supported as it does rotations. *Please note: these are sold individually, however there are two of these in your appliance. We recommend that these be replaced at the same time, this allows for optimal performance and ensures they wear evenly. Each ...Read moredrum glide is approximately 33 inches in length. If the following symptoms occur, consider replacing the drum guide as a solution: dryer is noisy, will not tumble, or leaves marks on clothes. Remember to unplug the power source to the dryer before installing this part. Refer to the diagram provided by the manufacturer for further instructions and guidance.

This dryer heating element produces heat to dry clothes and is located in the rear of a dryer. If the heater element is burned, the dryer does not heat or over heats, or clothes are taking too long to dry, replacing this part could solve your problem. The tools needed for this repair project are a Phillips screwdriver, putty knife, and ne...Read moreedle nose pliers. To repair, first remove the main top of the dryer and ground strap at the rear. Disconnect the two wire harnesses and remove the screws that hold the front panel to the cabinet, in order to pull out the front panel. Now that you have access to the inside of the dryer, refer to the manual for further installation instructions and detailed guidance. Remember to unplug your appliance from the power source before beginning this repair project.

The door catch on your dryer is an important part as it keeps your dryer door closed, in order to ensure no air or clothes can escape. This part works by holding the door strike, which allows the door to stay secure. Before you begin this repair make sure to disconnect the power supply to the dryer. The tools you will need for this instal...Read morelation include a Phillips screwdriver and a small flat blade screwdriver. A pair of pliers may also come in handy. Users ranked this repair as easy, and say that it will take fifteen minutes or less to complete.

The dryer thermal limiter, also known as a thermal fuse, blows the fuse to cut off power to the dryer when the dryer begins to overheat. Once the dryer reached 220 degrees Fahrenheit, the heat cuts out. If the thermal fuse is defective, damaged, or blown up then the dryer wont start, especially since it cannot be reset. It must be replace...Read mored if the following symptoms occur: the dryer overheats, takes too long to dry clothes, or there is not enough heat in the dryer. The tools needed for this repair are, a screwdriver, putty knife and needle-nose pliers. This part is manufactured for both gas and electric dryers.

The lower front felt seal with adhesive, also known as a drum felt seal, is used in dyers and allows the drum to easily glide on the front panel. For this repair project, you will need the following tools: #2 Phillips screw driver, #2 square head screw driver, putty knife, and wire bush. If your dryer will not tumble, or makes a squeaking...Read more noise when running, replacing this part could solve the problem. Remember to unplug your appliance from the power source for safety before you begin this installation project. Refer to the manual provided by the manufacturer for further installation instructions.

This drum bearing bracket is for dryers. Drum bearing bracket holds and supports the drum bearing

This high limit thermostat is used in a dryer and monitors the temperature to make sure it does not exceed 260 degrees Fahrenheit. When your dryer temperature reaches 260 it will cut it out and only comes back when it drops by at least 70 degrees Fahrenheit. If your dryer is overheating, taking too long to dry clothes, or is not producing...Read more enough heat, replacing the thermostat could be the solution to your problem. The tools needed for this part are a Phillips screwdriver, putty knife, and needle nose pliers. Refer to the manual provided by the manufacturer for installation instructions and guidance.

Located at the front of the dryer, this lint filter traps lint and debris from the exhaust air flowing out of the dryer drum. This part measures approximately 12 inches long x 7 inches high, has a plastic frame, and a mesh body to catch debris. If your filter needs cleaning, the dryer cycle will take longer due to a buildup of lint or fab...Read moreric softener affecting the air flow through the filter. If there is a buildup, try scrubbing the filter with hot water and soap. If the filter is damaged or torn, it should be replaced. Cleaning the lint filter before starting the drying cycle is a great way to ensure your dryer performs properly.

The door strike is attached to the door of your dryer and holds the door closed. If your dryer door is not closing, this might be due to the door strike needing to be replaced. This is a simple repair that should only take a few minutes to complete. The package contains one strike. Open the dryer door, and use a flat head screw driver to ...Read moresnap the old strike out if it has not fallen out already. Simply push the gasket out of the way, squeeze together the strike and place inside of the opening. Wiggle to ensure it is set in place properly.