ADE7000AYW Admiral Dryer - Instructions

First and Foremost i was told that my problem was with the Thermal Fuse (Fix Ya.com), Then with the little Electrical knowledge I have thought Fuses don't turn on and off,If the fuse was bad i would get No Heat. (Even for a second) Fuses just don't turn on and turn off intermittently,when they go there done! So after a little research i d ... Read more ecided to order the gas coil valve. I tilted the top up, two screws on the front panel, took that off and the valves were exposed,(bottom left) two screws too remove bracket then installed new coils on bracket,put back together and I Have Heat Again! NO problems what so ever since new install. I would say having not been for cleaning lint build up inside the machine (been 6 years) the Whole project took me Ten Minutes.

Same as others.
1. Unplug dryer from power source
2. Use nut driver to remove two front screws at bottom of dryer
3. Disconnect cable connected to Secondary Coil (this is the coil towards the rear of the dryer)
4. Use angled phillips screw driver to loosen screws holding cap on top of the two coils. (Angled tool not ... Read more required but seemed easiest to me)
5. Slide top cap back towards lock screw to allow coil to be lifted out
6. Remove and replace secondary coil
7. Replace cap, tighten screws to lock in place, reconnect cable to coil
8. Restore power to dryer, test and confirm gas flame stays lit
9. Replace lower front panel on unit

PartsSelect a great resource to use for home repairs like these. My first time using site and doing this type of work, now PartsSelect my first source to go to on such items.

First I put the square female end iof the door catch kit nto the square hole as snug as I could. Then I gently pushed the door against the piece until I heard it click in to place. That's it!! Sooooo simple--

I received the part I ordered immediately and the included instructions made installation a snap. Thank you for your help. I would not hesitate to order from your company again.

I noticed my dryer was heating, but not tumbling. I"m a 53 year old single female, and my dryer I bought used 3 years ago. I had no clue what the problem was. I texted my brother and said, "it heats but doesn't tumble - is it shot?" He texted back "probably the drive belt - pop the top and see." So I popped the top, and sure enough, t ... Read more he belt was broken. So I googled "diy + dryer + drive belt" and watched a You Tube video. I then drove all over town looking for a belt, and the only place that carried it had closed at noon (saturday). So I googled " appliance parts + dryer and came to this site, ordered the part and it was delivered in two days.
I borrowed a nut driver from my brother, removed the front of the dryer, used a plastic cup to prop up the drum. I put the belt on the drum, being sure to place the ribbed side down, looped through the pulley and onto the motor, removed the cup, put the front back on, dropped the top, replaced the lint trap and the two screws holding that in place, turned the dryer on and voila! All done.

removed front cover, lifted drum up with a clamp and replaced slides. Replaced front cover

Unplug dryer

Pick the top up at the front and swing up. Inside each side of the front is a screw to remove. Do not forget to unhook the door switch wires. Pull the drum. Push belt off as you remove the drum. Works better to reach in at the lower right and take the belt off of the tighener first.

After you clean o ... Read more ut any lint in area unplug the wires from the motor and snap off the hold down clamp on the back bearing.

The blower needs to be released fromt he shaft. The snap ring in front of the blower needs to be taken off. This can be done with a screw driver by prying off the flat spot on the shaft. However, a snap ring pliers would be better. The front of the blower housing must come off as the blower must come off. There is a snap ring behind the blower that must come off also.

The biggest problem I had was removing the front motor bearing housing from the plastic blower housing. It is easy once you see that the front bearing housing is held in by four tabs in the plastic housing. By rotating the front bearing housing 90 degrees you will be able to pull it out.

From there just reverse your action. The belt went on ok. I found by putinng the belt on the drum and the motor drive pully first I was able to reach in an put the belt over the tighener.

Removed and replaced both the thermostat sensor and the ignitor. Tested thej dryer and it worked. Replaced the front panel and it was good to go.

my ex husband took the top and front of dryer off and removed the drum and belt. he pulled off the worn roller and replaced it with the new one. we put the drum in backwards and had to turn it around but all went well and the dryer is quiet again!!!

After reading the many different common stories,I replaced both coils (m series).Very simply lifted up the top of driver,held by 2 snap springs and 2 lint vent screws.Removed front cover,2 screws and 2 bottom snaps,coils down on bottom left.r/r both coils,reinstalled covers and let there be heat!This website is a blessing!!

Replaced coils on gas valve.

I removed the Drier Door and removed the Front Drier Panel exposing the Gas Valve & associated parts. I removed two (2) screws holding the Gas Valve Coils in place & replaced the 2 terminal coil, then replaced the screws, Front Cover & Drier Door. I liked the results so much, I ordered the other Gas Valve Coil and will replace it also w ... Read more hen it arrives.

Good trouble shooting information.

Step 1. UNPLUG DRYER
Step 2. Remove the selector knob(timer). It just slides off by pulling it toward you.
Step 3. Remove the back cover of the Control Panel. Three phillips screws along the top and three 1/4" hex head screws along the back. After removing the fasteners lift up on the panel and it can be removed.
Step 4. R ... Read more emove the two 1/4 hex head screws that hold the timer to the control panel. (They are on the front of the control panel under the selector knob that was removed in step 2.)
Step 4. Switch over the wires one at a time from the old timer to the new timer. Don't forget to switch over the resistor.
**Note**Also pay attention to original position on the timer, it can be installed 180deg's out(upside down) then the knob will not be indexed poperly with the control panel.
Reverse the steps to reassemble!

popped up top of dryer -- With pliers squeezed clips on inside of latch - - with screw driver pryed latch out -- just pused new latch in.......... Thanks to parts select for sending part sooo fast.. wife was happy.. Thanks, Dale

I opened the top then i did change the heater element kit only one screw out and finaly replace the temperature switch, again one screw out was realy ease was my first time,the professional online help my, every one can do it thanks i appreciate your help.H.E.K.P/N AH2162280 - temp/switch p/n 31001449.