If the bucket is full indicator on your dehumidifier is on but the bucket is empty, you may have a problem with the float. If you notice that the float is warped or damaged, it should be replaced. This device is located near the bucket and prevents the dehumidifier from overflowing. You will need to open up the dehumidifier to complete th...Read moreis repair. This product is approximately 4 inches in length. Many of our customers have rated this repair as easy. To complete the repair simply remove the clips that hold the float in place, attach the new float, and replace the clips.
This hex nut is an authentic Whirlpool part that is sourced directly from the original equipment manufacturer, and will fit a variety of appliances including ovens, microwaves, refrigerators, air conditioners, and dishwashers. It is a metal part with a threaded hole to fasten parts in the appliance together. It is common for this part to ...Read morewear out; it is recommended to order a spare. To replace this part the tools needed are a nut driver or wrench. This nut features a built-in external tooth lock washer, which is used to help keep the nut in place.
This part is for your dehumidifier. The bucket water level switch is used to prevent water overflow when the bucket is full. You will not be able to tell if the switch has failed just by looking at it. You will need to perform a continuity test. This will determine if a continual electrical path is present. If you notice that dehumidifier...Read more will not run even when the bucket is empty, it might be due to the switch needing to be replaced. To access the part, you will need to remove all the outer housing. The switch is located in a plastic holder found on the inside wall.
The float clip works in a humidifier to ensure the float functions properly. The float is located near the humidifier bucket and monitors the water level as it rises and the clip keeps it in place. The float makes sure the water level is balanced and does not over flow. This float triggers the flow switch to shut off. If there is a defect...Read more with the clip, it can be a safety hazard as it might not be able to detect and stop an overflow. Make sure to unplug the dehumidifier from the power source before starting this replacement project as a safety precaution.
A zip tie, also known as a cable tie or a wire tie, is a fastening device that holds wires or tubing together. If a machine has wires or tubing that are easily shifted, you need to hold them tightly together using a zip tie. It is a flexible, plastic strip that has serrated teeth and a locking mechanism. If the zip tie is damaged, it shou...Read moreld be replaced. Freely moving wires may rub against surfaces, causing them to break over time. Zip ties are single-use and may not be reused after they are removed from a machine. To release the locking mechanism, you will need to insert a small flat tool into the head of the zip tie, between the tongue and the serration, and depress the bar. You can then pull the teeth out of the mechanism to loosen the cable tie. This part is produced by the original equipment manufacturer and is sold individually.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
the dehumidifier was not shutting off when water level was full
5 of 9 peoplefound this instruction helpful.
Steven from Owings Mills, MD
Really Easy
Less than 15 mins
replaced a piece of the plastic at the top of the bucket that seems to be the water gauge. this seems to be fixed. we are very happy
Was this helpful?
Thank you for voting!
float was missing
2 of 5 peoplefound this instruction helpful.
barbra from STERLING HTS, MI
Really Easy
Less than 15 mins
Screw drivers
pried off the plastic fastener with flat blade screw driver set new float in place then pressed plastic fastener back in place
Was this helpful?
Thank you for voting!
Push on connectors and switch housing were different
0 of 1 peoplefound this instruction helpful.
Lester from Brazil, IN
A Bit Difficult
30 - 60 mins
Screw drivers
The switch housing was not exactly the same for easy snap in. I removed the actual switch and installed it into the old housing. Then I found that the male pins were larger than the old ones. I chose to clip off the female connectores, strip the wires, and solder the wires to the pins on the switch. It was easier for me than attempting to
... Read more change the push on connectors. For me, the actual switch was what I wanted and I fixed it my way. It was easy to do however some folks may want to change the push on connectors. Works great and saved me hundreds of dollars. Thanks.