My Orders
AD25TH0 Whirlpool Dehumidifier - Overview
Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".
Search filter:
Clear Filter
Your search term must have 3 or more characters.
No Longer Available
Dehumidifier Float
Part #WP1172075
If the bucket is full indicator on your dehumidifier is on but the bucket is empty, you may have a problem with the float. If you notice that the float is warped or damaged, it should be replaced. This device is located near the bucket and prevents the dehumidifier from overflowing. You will need to open up the dehumidifier to complete th...Read moreis repair. This product is approximately 4 inches in length. Many of our customers have rated this repair as easy. To complete the repair simply remove the clips that hold the float in place, attach the new float, and replace the clips.
Read less
No Longer Available
Bucket and Float Kit
Part #8201783
This bucket and float kit, also known as water tank assembly, is for a dehumidifier is 14.5 inches long and 8.5 inches wide. The water tank extracts, traps, and contains the moisture from the air, which dehumidifies your room. The kit contains one bucket, one flat, and two screws for installation. The bucket is white and made of plastic. ...Read moreYou may need to replace this part if your dehumidifier is no longer trapping the water properly. This is an authentic part from the genuine manufacturer, and you cannot order the parts individually.
Read less
$7.47
In Stock
Refrigerator Single Hex Head Screw
Part #WP489069
Sold individually. The size of this screw is 1/4" hex head and 10-12 x 1/2".
No Longer Available
Dehumidifier Humidistat Control
Part #WP1168670
The humidistat control, used in dehumidifiers, switches the dehumidifier on and off automatically to maintain humidity. If the switch does not work, the humidifier will not maintain the temperature properly. For this repair, screwdrivers are the only tools needed. First remove the knob and the screws from the top. Pry back the plastic ret...Read moreainers on one side of the old humidistat and remove wires before installing the new part and reattaching the two wires that connect to it. Remember to unplug the humidifier from the power source before installation.
Read less
$7.47
In Stock
$65.73
Special Order
Bucket Water Level Switch
Part #1188814
This part is for your dehumidifier. The bucket water level switch is used to prevent water overflow when the bucket is full. You will not be able to tell if the switch has failed just by looking at it. You will need to perform a continuity test. This will determine if a continual electrical path is present. If you notice that dehumidifier...Read more will not run even when the bucket is empty, it might be due to the switch needing to be replaced. To access the part, you will need to remove all the outer housing. The switch is located in a plastic holder found on the inside wall.
Read less
No Longer Available
Float Clip
Part #WP1186430
The float clip works in a humidifier to ensure the float functions properly. The float is located near the humidifier bucket and monitors the water level as it rises and the clip keeps it in place. The float makes sure the water level is balanced and does not over flow. This float triggers the flow switch to shut off. If there is a defect...Read more with the clip, it can be a safety hazard as it might not be able to detect and stop an overflow. Make sure to unplug the dehumidifier from the power source before starting this replacement project as a safety precaution.
Read less
$7.47
In Stock
Zip Tie
Part #WPW10339879
A zip tie, also known as a cable tie or a wire tie, is a fastening device that holds wires or tubing together. If a machine has wires or tubing that are easily shifted, you need to hold them tightly together using a zip tie. It is a flexible, plastic strip that has serrated teeth and a locking mechanism. If the zip tie is damaged, it shou...Read moreld be replaced. Freely moving wires may rub against surfaces, causing them to break over time. Zip ties are single-use and may not be reused after they are removed from a machine. To release the locking mechanism, you will need to insert a small flat tool into the head of the zip tie, between the tongue and the serration, and depress the bar. You can then pull the teeth out of the mechanism to loosen the cable tie. This part is produced by the original equipment manufacturer and is sold individually.
Read less
No Longer Available
No Longer Available
PAN-DRAIN
Part #1168761
No Longer Available
Control Knob - White
Part #1168687
$52.67
In Stock
VALVE
Part #978030
This access valve is an authentic manufacturer parts kit used in appliances with a refrigerant such as the refrigerator and air conditioner. This kit includes a valve body, valve core and a valve cap. The body and cap are made of brass while the core is made from steel. If you notice that your appliance is leaking, not cooling adequately ...Read moreand the valve components are corroded, you should replace the access valve. As part of your general maintenance, you should also replace the valve if your appliance is more than 10 years old and the valve has never been changed. Use a valve wrench to remove the valve cap and use a core removal tool to pull out the core. Install the new valve body, core and cap and ensure they are securely fitted. Note that these parts are sold together.
Read less
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!
View More