Quick Question!

Have you ever purchased from PartSelect.com before?

Models > ACG150NLD0

ACG150NLD0 Frigidaire Refrigerator - Overview

Get Parts and Repair Help for ACG150NLD0

If you know the refrigerator repair part you need, you can browse the list of all parts on the ACG150NLD0, or you can search by name or part description. You can also find your part by where it is located on the ACG150NLD0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for ACG150NLD0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the ACG150NLD0

[Viewing 3 of 3]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$7.94

SOCKET

The light socket on your refrigerator houses the light bulb and connects it to the power source. If you notice that your refrigerator light does not come on when you open the door,...

$5.21

Door Shelf End Cap - Left Side

$45.67

Door Shelf Retainer Bar - Cut to Fit

This is a white cut-to-fit door shelf retainer bar.

$6.25

Door Shelf End Cap - Right Side

This white end cap is a little over two inches long. It is used for the right side of either the refrigerator of the freezer door shelf.

$3.77

Door Shelf End Cap - Left Side

$3.63

Door Shelf End Cap - Right Side

$6.69

Hexagonal Screw

Sold individually.

$9.73

LAMP

$2.58

Ice Cube Tray

The ice cube tray is made of plastic, is white in color, and is sold individually. This is a part for your freezer. The ice cube tray is sturdy but flexible to allow you to easily ...

$9.42

Filter - Drier

A filter-drier in a refrigerator has two essential functions. The first is to absorb system contaminants, such as water, which can create acids. The second is to provide physical filtration. This means trapping moisture, small metal chips, and dirt found in the refrigerant gas. If your refrigerator motor is constantly running, but the refrigerator is not getting cold, the issue could be due to a damaged or faulty filter-drier. Faulty filter-driers are sometimes the cause for abnormal freezer compartment temperatures and partially frosted evaporators. This filter-drier is approximately 11 inches long. Remember to disconnect the power from your refrigerator before beginning this repair.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Light socket melted around bulb

  • Customer: William from Alexandria, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 51 of 88 people found this instruction helpful
After unsuccessfully trying to change the blown light bulb I discovered that the plastic light socket had gotten so hot that it melted and permanently fused with the blown bulb. After my new socket arrived in the mail I just popped the temp control assembly out with a screw driver and removed the old socket and placed the new one in. Whole operation to 5... read more

Freezer stopped freezing food.

  • Customer: FREDDIE from WHITAKERS, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 14 of 19 people found this instruction helpful
I unplugged electrical cord to the freezer. I removed the cover to the relay and load protector. I labeled the wires and made a diagram on the proper placement of each wire going to the relay. I unplugged each wire and removed the relay. Then I removed the load protector. I installed the new load protector and new relay. I placed the wires on the proper term... read more

Drip pan had rusted & was leaking water on the floor

  • Customer: John from Forest, VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Wrench (Adjustable)
  • 9 of 10 people found this instruction helpful
The BIG problem was getting the old drip pan off. The bolt on top of the compressor was too long to allow the removal of the old drip pan. I removed the old drip pan by cutting most of it away with tin shears then cutting the remaining part of the pan around the bolt with a hack saw (taking care not to damage freon lines and raising the pan above the threads... read more