This part is located on the drum roller support shaft in your dryer appliance. The exterior of the washer is 1 inch in diameter with a hole in the middle and is made of metal. They are installed alongside the drum support rollers and idler pulleys. If you notice that your dryer is making an unusual sound it could be due to the washer beco...Read moreming loose on the drum support. They help prevent the rollers and pulleys from bumping up against the brackets they are installed on. If you are replacing the rollers, we suggest you replace the washers at the same time.
This part is sold individually. The air filter is part of your room air conditioner and prevents dirt, dust, and other debris found in the air from getting inside your home. Over time this part can become worn and filled with dirt. It measures 19 inches in length and 12 inches in width. It is important to keep the filter clean and well-ma...Read moreintained to ensure your air conditioner is working efficiently. The filter is found behind the front grill. This is an original part that comes directly from the manufacturer.
This hex nut is an authentic Whirlpool part that is sourced directly from the original equipment manufacturer, and will fit a variety of appliances including ovens, microwaves, refrigerators, air conditioners, and dishwashers. It is a metal part with a threaded hole to fasten parts in the appliance together. It is common for this part to ...Read morewear out; it is recommended to order a spare. To replace this part the tools needed are a nut driver or wrench. This nut features a built-in external tooth lock washer, which is used to help keep the nut in place.
This motor clip is an original manufacturer replacement clip used to secure the motor in your home appliances. It holds the motor firmly to its housing to prevent shaking and potential damage while the appliance is in use. Over time the clip can fail due to exposure to high temperatures, vibration, and humidity resulting in an unstable mo...Read moretor and decreased performance. Remove and discard the faulty clip and place the new one in its position. Align it appropriately with the motor and mounting bracket before securing it in place. Be sure to check your equipment specifications as your appliance may require two clips to complete the repair, and this clip is sold individually.
This screw is sold individually. It is a genuine OEM replacement part, and it is designed for use with refrigerators. Most often it is used with the ice bucket ice deflector, retainer clip, and front cover. Due to varied uses we recommend referring to model-specific diagrams for exact placement. This screw measures 8-18 by 1/2 inch.
Silicone rubber adhesive is a high temperature adhesive that is used for gaskets on dryers and felt seals. It is used on many different appliances for many different application reasons. This silicone paste creates a waterproof seal between components. This product is a 2 oz. tube. Unplug your appliance if you will be working on any inter...Read morenal workings and applying this sealant. Wear gloves to protect your hand from accidently applying sealant to your skin. The surface must be clean, dry, and free from oil and grease. Coat one surface and let it dry for at least one minute and then bond.
A zip tie, also known as a cable tie or a wire tie, is a fastening device that holds wires or tubing together. If a machine has wires or tubing that are easily shifted, you need to hold them tightly together using a zip tie. It is a flexible, plastic strip that has serrated teeth and a locking mechanism. If the zip tie is damaged, it shou...Read moreld be replaced. Freely moving wires may rub against surfaces, causing them to break over time. Zip ties are single-use and may not be reused after they are removed from a machine. To release the locking mechanism, you will need to insert a small flat tool into the head of the zip tie, between the tongue and the serration, and depress the bar. You can then pull the teeth out of the mechanism to loosen the cable tie. This part is produced by the original equipment manufacturer and is sold individually.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Filter was filthy, no telling how long it had been since changed
10 of 14 peoplefound this instruction helpful.
SHIRLEY G. from Mabank, TX
Really Easy
Less than 15 mins
Took out old filter and replaced it with the new filter
Was this helpful?
Thank you for voting!
old filter had become brittle & needed replacing
5 of 11 peoplefound this instruction helpful.
Rhea from Plainview, TX
Really Easy
Less than 15 mins
Just removed the old filter and replaced. Slid right in, no tools required.
Was this helpful?
Thank you for voting!
Needed new Ice Maker
5 of 11 peoplefound this instruction helpful.
Joseph from Liberty, MS
Easy
30 - 60 mins
Nutdriver, Screw drivers, Wrench (Adjustable)
Removed back cover, and installed the water valve. Removed the water supply tube cover and installed the supply tube. Opened freezer and removed the electrical cover, removed the knockouts and pulled line out. Hooked up ice maker and installed it to wall. Turned water on and waited a couple hours, it is making ice. Installing the ice
... Read more maker was easy. Running water line to it........well that is another story. LOL.