This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these replacement bulbs are most often used to light the inside of refrigerators and ranges. It features a standard socket base, which means you simply unscrew the burnt-o...Read moreut bulb and screw in the replacement. Depending on the appliance you may require a screwdriver or nut driver to access the light bulb. We recommend you wear work gloves while handling this replacement part. It is constructed of glass and metal and is sold individually. Depending on the appliance and location of the bulb within it, you may want to consider disconnecting power and using a flashlight for easier access to unscrewing and re-screwing in your bulb during this repair.
This long oven sensor is also commonly known as a temperature sensor. It is designed for use with ovens and ranges. It is similar to a thermostat; it measures and regulates the internal temperature of your oven cavity. There is an adapter at one end, a probe at the other, and they are connected by an insulated wire. The probe is approxima...Read moretely 7 inches long. You can test the sensor with a multi-meter for functionality. You need to check the model-specific manual to determine what the proper resistance is for your specific appliance. This oven sensor comes with two wire harness adapters and a set of instructions.
This oven rack is used for the inside your oven range to provide a stable surface for your cookware for baking/broiling. The oven rack measures approximately 23.5” x 16”, is made of metal and is chrome in color. This oven rack is a genuine OEM part and is sold individually.
This bake element for your oven, range, or stove provides heat from the bottom of the appliance to cook or bake your food items. You may need to replace this part if your oven is not heating properly. This bake element is approximately 22 inches wide. Disconnect power to your appliance before completing the repair because you will be work...Read moreing near electrical wiring harnesses. The wiring harnesses feature slip-on terminals for easy installation. Be sure to hold the wiring harness forward so they do not fall behind the panel, as they are difficult to retrieve. This is an authentic OEM bake element.
The light cover lens in your oven is designed to protect the light bulb. If your light cover lens is damaged, you will need to replace it. This part is made of clear glass and is roughly 3 inches in diameter. Many of our customers have rated this repair as easy, and it should take less than 10 minutes to complete. In order to do this repa...Read moreir, simply unscrew the old light cover lens, and replace it with the new one. If your old light cover lens is damaged, be careful of any broken glass when completing this repair.
This oven door gasket prevents heat from escaping the oven cavity when in use. This is a very easy repair that should only take a few minutes. The door gasket may damage or rip over time due to repeated use. If you notice that hot air is escaping from your oven, it is likely that the gasket needs to be replaced. You will need to open the ...Read moreoven door and remove the old seal by pulling it out of place with your hands. The old gasket will be secured with clips that will come out when you pull the entire piece out. The new gasket will have hooks all along the rim, which will line up with the oven door. Simply line up the hooks and push into place outlining the door of the inside of the oven. No tools required.
This oven light assembly is a little over four inches long and comes with the lens and 660-watt light bulb. Make sure your appliance is unplugged or circuit breaker is off before installing this new part. It is located inside the oven and may need to be replaced if the socket has failed, causing the light to not come on inside the oven. I...Read moret may also need to be replaced if you notice that the glass is broken and the whole assembly needs to be replaced. The part is located in the upper right hand side of the oven. To reach the bulb you will need to open the oven door and remove the upper rack.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven not holding 350 F, when cooling the coils did not reheat
162 of 213 peoplefound this instruction helpful.
David from Westford, MA
Really Easy
15 - 30 mins
Screw drivers
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening,
... Read morereinstall 2 screws. The oven works fine! Note that due to thermal lag the temperature overshoots to 370 degrees and undershoots to 340 degrees, this appears to be normal oven operation. Putting door back in place was easy.
Read less
Was this helpful?
Thank you for voting!
F1-1 code
79 of 110 peoplefound this instruction helpful.
charles from marstons mills, MA
Really Easy
Less than 15 mins
Screw drivers
First I removed the two screws that hold the element in place. I then pulled the sensor out about 3 inches and disconnected the two wires. Next, I connected new sensor and screwed the new sensor back in place. One area for caution. Make sure that the electrical connection is pushed in past the insulation on the back side of the oven. Fa
... Read moreilure to do so will cause the plastic plug connector to melt from oven heat.
Read less
Was this helpful?
Thank you for voting!
Repeated oven temperature sensor fault codes.
35 of 43 peoplefound this instruction helpful.
David from Arlington, VA
Really Easy
15 - 30 mins
Screw drivers
First I removed the two philips screws inside the oven that hold the element in place. Then I pulled the sensor out and the two insulated wires through the hole to reveal the plastic connector. I unsnapped it from the connector and replaced it with the new element. Then, behind the oven, I removed five or six philips screws on the righ
... Read moret side of the large panel so I could pull the wires back through the layer of fiberglass insulation to make sure only the sensor itself would be exposed to the oven's heat. I then secured the back panel again and replaced the two philips screws holding the sensor in place.