AB2526PEKW3 Amana Refrigerator - Instructions

Remove Crisper drawers from Bottom Shelf.
Remove glass from the top of Bottom Shelf.
Drop new Crisper frame center rail into slots on the top of the Bottom Shelf shelf.
Replace glass onto the top of the Bottom Shelf.
Slide drawers between left and right guides and the Crisper frame center rail.

Total repair ... Read more time less than one minute.
No tools required.

The video on website is very good and explains everything in detail. Just follow the directions. This is EASY!!!!

I used a flat-head screwdriver to pop out the old light rocker switch. Then, I unplugged the wires, plugged them into the new light rocker switch, and then popped the new switch into the hole. That's it! Lights began working again.

I used a flat screwdriver and released the lock tab on the bottom of the light switch, and pried the switch out, being careful to not damage the plastic around the mounting place of the switch, unplugged wiring from old switch, plugged in the new one and pushed the new switch into place. Job finished light switch now working.

We had periodic leaks from under the Unit from new, could never figure out where it was coming from. Finally as it began to cause damage to surrounding cabinets, we took the back off and found the multiple cracks in the drip pan. Someone had hand trucked it from the wrong side! It was difficult to figure out the fan removal (it sits in th ... Read more e pan) but push the top forward and pull the bottom back and the fan came out. Then the pan was simple to remove / replace, by reversing the removal procedure, the fan was re installed.

An easy job for smaller hands. Removed the two bolts holding the light cover. Removed two electrical connections from the old switch by pinching the retaining clip,removed the switch, snapped in the new one and re-attached the connectors. Your online illustrations helped me to know that the plastic housing for the light switch would only ... Read more swing down so far and was not intended to be removed. Saved me from breaking that plastic cover's tabs. This home repair saved me more than 5 times the cost of hiring a professional to do it. Very happy homeowner.

Through out broken plastic, replace with new one
to be replaced in a few years.

Remove the light cover. Use a flat head screw driver to push in the tabs on the back of the program mount and pull down to expose the computer board. The Thermistor is clipped on under the vent holes on the right side. Cut both wires to remove the old thermistor strip a 1/4 inch off the remaning wires and the new thermistor wires twist bo ... Read more th ends together crimp on the wire caps snap in the new thermistor reinstall the program board until the retainer clips snap into place, slide the light cover back on.

Once I saw the replacement part I understood how to pry out the switch with a small screwdriver. Then just unplug the old one, plug in the new one and pop it into place.

The PartSelect site made it easy to correctly identify the correct part, it was inexpensive, and the shipping was fast.

I'm very pleased!

Since it was apparent the crisper glass is fragile I was very careful to not stress it. I opened the box then took a large board almost as big and slid it on. I carried both items to the fridge and with both doors open slid the glass into place. I am 65 yrs. Old and have owned many refrigerators but this is a first. They don't build t ... Read more hem like they use to. .

Watched Partselect video of P-trap installation.Removed water line & back cover& disconnected wires to water solenoid .Removed old drain tube & old problematic rubber funnel. Used contact cleaner to clean rubber residue from drain line and used a little silicone to aide reassembly. Job went well thanks to video.

The repair seemed simple, I just needed to remove the old bracket -- 4 screws -- and slip the new one on.

The tricky bit is that the roller bracket holds the weight of the fridge. So in order to make sure that the fridge did not fall over, and to keep the installation point off the ground so that I could align the screw holes, ... Read more I needed to shim up the side of the fridge that I was working on.

To tap in the shims, I used a hammer and a spare chunk of wood. I ultimately used 3 shims, and kept tapping until the roller wheel could roll freely. Then I knew that the fridge was high enough. After that, it was pretty easy to remove the 4 screws, align the new bracket, and replace the screws. After that, in order to get the shims out I could just extend the foot brake as it was designed, and that lifted the fridge enough for me to easily slide out the shims. After that I just had to level out the fridge by adjusting the two feet.

It was great. We replaced the thermistor A little difficult to get to the thermistor but once we found it five minutes. My refrigerator seems happy but we will monitor it and see.

well, first, after calming down i removed the glass from my sink (this took a half hour). then i went to the computer and looked for jenn-air parts. the part-select site came up. the site was very easy to use and although i usually leave things like this for my husband to do i decided to order the part myself, which i did.
the trick ... Read more was finding something on hand to cover the tops of the crispers which were both full of vegetables. i innovated and used a shallow broiler pan and its lid which covered 90% of both the crispers. the part came in five days unwrapping the part was easy, cleaned it with windex (no sink soaking this time) and inserted it on top of crispers............totally easy!!!!!

tested bulb good ,replaced door switch first(least expensive)then ordered light socket and circuitboard.If clicking sound is heard replace circuitboard first to save on return shipping because the switch and socket where ok